1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. David Sale
    Post

    Solved Cleaning Clogged Nozzles

    Understood. Thank you for the insights. The way I had envisioned using the item was handheld instead of a drill. Also while the Hotend was...
    Post by: David Sale, Jan 6, 2017 in forum: Troubleshooting
  2. David Sale
    Thread

    Solved Cleaning Clogged Nozzles

    Came across a product for cleaning clogs in the nozzle . I have not tried it yet, but thought of the forums....
    Thread by: David Sale, Jan 5, 2017, 6 replies, in forum: Troubleshooting
  3. David Sale
    Post

    Solved To Low

    Thank you much! Think the extruder was to hot. Other weeks helped out as well!
    Post by: David Sale, Dec 12, 2016 in forum: Troubleshooting
  4. David Sale
    Post

    Solved To Low

    Okay, I believe that has helped or resolved the issue of it "digging" in to the tape. I have another issue. On larger, flat, opjects the...
    Post by: David Sale, Dec 12, 2016 in forum: Troubleshooting
  5. David Sale
    Post

    Solved To Low

    Yes, I am using Matter Control. I am attepmting to offset Z by 1mm right now. I believe this corrected the issue. Going to make a couple prints...
    Post by: David Sale, Dec 12, 2016 in forum: Troubleshooting
  6. David Sale
    Thread

    Solved To Low

    When I start a new print it is as if the extruder is 1 or 2 mm "to low". The Extruder Tip will dig in to the tape sometimes. After the first pass...
    Thread by: David Sale, Dec 12, 2016, 5 replies, in forum: Troubleshooting
  7. David Sale
    Post

    Solved Extruder Fan replacement specs.

    Just a note. I would recommend which ever fan you decide on, look at the Tip for that fan and order the 'Socket' or 'Receptacle' also. The idea...
    Post by: David Sale, Nov 28, 2016 in forum: Troubleshooting
  8. David Sale
    Post

    Solved Extruder Fan replacement specs.

    Understood, thank you very much for your help! :-)
    Post by: David Sale, Nov 23, 2016 in forum: Troubleshooting
  9. David Sale
    Thread

    Solved Extruder Fan replacement specs.

    A little background, in case any one was wondering. I work at a technology department. We sell the RoBo 3D printer. The demo unit has a few...
    Thread by: David Sale, Nov 23, 2016, 8 replies, in forum: Troubleshooting
  10. David Sale
    Post

    Solved RoBo R1 (not Plus) Take apart help request.

    Thank you again. Turns out there were 3 screws holding the paired boards. These screws were not well seated. Two had fallen out completly. The...
    Post by: David Sale, Nov 22, 2016 in forum: Troubleshooting
  11. David Sale
    Post

    Solved RoBo R1 (not Plus) Take apart help request.

    Thank you much!
    Post by: David Sale, Nov 22, 2016 in forum: Troubleshooting
  12. David Sale
    Thread

    Solved RoBo R1 (not Plus) Take apart help request.

    I am attempting to repair a store demo unit. A take apart guid is needed. Specifically, it will require for the base of the unit to be opened....
    Thread by: David Sale, Nov 22, 2016, 4 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again