1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Wgreisi
    Post

    Unresolved Print keeps failing

    So I was labeling the wires to swap the ramps and the 11A + connector is burnt too. These are the original components from Robo l. The connectors...
    Post by: Wgreisi, Mar 23, 2021 in forum: Troubleshooting
  2. Wgreisi
    Post

    Unresolved Print keeps failing

    That'll do it. I am assuming the ramps need to be replaced?[IMG] Sent from my SM-N975U using Tapatalk
    Post by: Wgreisi, Mar 23, 2021 in forum: Troubleshooting
  3. Wgreisi
    Post

    Unresolved Print keeps failing

    So now the bed won't heat up. Am I that lucky or are these issues some how related? Sent from my SM-N975U using Tapatalk
    Post by: Wgreisi, Mar 22, 2021 in forum: Troubleshooting
  4. Wgreisi
    Post

    Unresolved Print keeps failing

    I did see in the terminal that it dropped from 222 to 200 (failure point) over the period of 20ish reads. I understand that the was over probably...
    Post by: Wgreisi, Mar 22, 2021 in forum: Troubleshooting
  5. Wgreisi
    Post

    Unresolved Print keeps failing

    I did get that error. I unplugged and plugged everything back in both on the hotend and the ramps. So far the print has been running for 7+ hours...
    Post by: Wgreisi, Mar 20, 2021 in forum: Troubleshooting
  6. Wgreisi
    Thread

    Unresolved Print keeps failing

    I am having an issue with prints failing between the 2nd and maybe 20th layer (normally on the earlier side). I tried the same print 3-4 times...
    Thread by: Wgreisi, Mar 18, 2021, 14 replies, in forum: Troubleshooting
  7. Wgreisi
    Post

    Solved Issues with XXL screen

    Without changing anything, it looks normal now...sure, why not
    Post by: Wgreisi, Jun 23, 2017 in forum: Troubleshooting
  8. Wgreisi
    Post

    Replacement Part Fan

    Thanks
    Post by: Wgreisi, Jun 9, 2017 in forum: General Questions
  9. Wgreisi
    Post

    Replacement Part Fan

    I am looking for a part fan that will use the stock cable.
    Post by: Wgreisi, Jun 9, 2017 in forum: General Questions
  10. Wgreisi
    Post

    Replacement Part Fan

    Sorry, the part fan
    Post by: Wgreisi, Jun 9, 2017 in forum: General Questions
  11. Wgreisi
    Thread

    Replacement Part Fan

    What is a good replacement for for the R1+ Hex hotend?
    Thread by: Wgreisi, Jun 8, 2017, 18 replies, in forum: General Questions
  12. Wgreisi
    Post

    Solved Issues with XXL screen

    When the print is done, the screen dose not change. When the card is removed, it goes back to normal.
    Post by: Wgreisi, Jun 8, 2017 in forum: Troubleshooting
  13. Wgreisi
    Thread

    Solved Issues with XXL screen

    Is this normal? [ATTACH] This is the first time I have used the my R1+ since the addition of the LCD. It looks like this when I print from my...
    Thread by: Wgreisi, Jun 8, 2017, 4 replies, in forum: Troubleshooting
  14. Wgreisi
    Post

    Solved Err Message

    Just plugged in a new hot end and everything looks good, must have been the thermistor. Thanks
    Post by: Wgreisi, May 30, 2017 in forum: Troubleshooting
  15. Wgreisi
    Post

    Solved Err Message

    I Use Matter Control. It does not allow me to heat up. [ATTACH]
    Post by: Wgreisi, May 24, 2017 in forum: Troubleshooting
  16. Wgreisi
    Thread

    Solved Err Message

    Can anyone tell me what "ERR MINTMP" on the R1+ means, and how to fix it?
    Thread by: Wgreisi, May 24, 2017, 9 replies, in forum: Troubleshooting
  17. Wgreisi
    Post

    Answered Audrino Board & Ramps

    Thank you
    Post by: Wgreisi, Apr 11, 2017 in forum: Troubleshooting
  18. Wgreisi
    Post

    Answered Audrino Board & Ramps

    So I ruined the ramps, not the audrino? Will the XXL LCD connector plug into the board you used in the other thread?
    Post by: Wgreisi, Apr 11, 2017 in forum: Troubleshooting
  19. Wgreisi
    Post

    Answered Audrino Board & Ramps

    R1+
    Post by: Wgreisi, Apr 11, 2017 in forum: Troubleshooting
  20. Wgreisi
    Thread

    Answered Audrino Board & Ramps

    I think I fried my board, at least where the thermistor's plug in. I had the wrong wires plugged in and switched them while everything was on. The...
    Thread by: Wgreisi, Apr 10, 2017, 6 replies, in forum: Troubleshooting
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2