1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. KRGraphicsCG
    Post

    Head crashing with Probe Failure error, fixed I think

    Very true. I've been printing with PETG on the C2 (this printer still operates well, even 7 years later) and it's an absolute beauty. On occasion,...
    Post by: KRGraphicsCG, Jan 19, 2024 in forum: Troubleshooting
  2. KRGraphicsCG
    Post

    Head crashing with Probe Failure error, fixed I think

    I've been dealing with this bs for the last several weeks with my C2 and while I mostly get successful prints with blue painters tape, I sometimes...
    Post by: KRGraphicsCG, Jan 18, 2024 in forum: Troubleshooting
  3. KRGraphicsCG
    Post

    Robo's new Buildtak

    Wait, the default surface is BuildTak?! I've never noticed this and now it looks like I can stop buying the sheets and just use the printing...
    Post by: KRGraphicsCG, Jan 15, 2024 in forum: Show and Tell
  4. KRGraphicsCG
    Post

    C2 - 2nd Print with PETG

    I have been printing with PETG for MONTHS and I have nothing but great news about it. The brand of PETG I am printing with DOES NOT require a...
    Post by: KRGraphicsCG, Jan 15, 2024 in forum: Show and Tell
  5. KRGraphicsCG
    Post

    If the print isn't sticking to the build plate, does that mean I need new tape?

    I will try using a skirt on the next piece.
    Post by: KRGraphicsCG, Oct 25, 2017 in forum: General Questions
  6. KRGraphicsCG
    Post

    If the print isn't sticking to the build plate, does that mean I need new tape?

    I don't use Octoprint. I will try preheating the hotend before printing again. I am getting tired of having to fix warped prints at the bottom. I...
    Post by: KRGraphicsCG, Oct 25, 2017 in forum: General Questions
  7. KRGraphicsCG
    Post

    If the print isn't sticking to the build plate, does that mean I need new tape?

    The initial layers for my raft is at 210 C and then down to 195C... I think that is my issue. The BuildTak will fix this issue.
    Post by: KRGraphicsCG, Oct 24, 2017 in forum: General Questions
  8. KRGraphicsCG
    Post

    If the print isn't sticking to the build plate, does that mean I need new tape?

    I am having some issues right now with trying to print a new piece... and I JUST PUT DOWN THE TAPE. The sides are gonna be slightly warped because...
    Post by: KRGraphicsCG, Oct 24, 2017 in forum: General Questions
  9. KRGraphicsCG
    Post

    Upgrading the Robo C2 with sound events - Instructions

    Like a DING sound when it finishes :)
    Post by: KRGraphicsCG, Aug 1, 2017 in forum: Mods and Upgrades
  10. KRGraphicsCG
    Post

    Solved Unlevel bed....

    Everything checks out... it is good... for now.
    Post by: KRGraphicsCG, Jul 22, 2017 in forum: Troubleshooting
  11. KRGraphicsCG
    Post

    Bed Not Raising, Buzzing Sound

    I will definitely keep an eye on this. I did a few tests this morning to make sure the motor is functioning and the bed raised correctly. I also...
    Post by: KRGraphicsCG, Jul 22, 2017 in forum: Troubleshooting
  12. KRGraphicsCG
    Post

    Bed Not Raising, Buzzing Sound

    So after talking to ROBO on Facebook, I ended up greasing the threaded rod, so that should stop the grinding stuff... doing a motor test now.
    Post by: KRGraphicsCG, Jul 22, 2017 in forum: Troubleshooting
  13. KRGraphicsCG
    Post

    Bed Not Raising, Buzzing Sound

    I'll keep an eye on it. I did notice at times it was harder to turn the rod manually
    Post by: KRGraphicsCG, Jul 21, 2017 in forum: Troubleshooting
  14. KRGraphicsCG
    Post

    Bed Not Raising, Buzzing Sound

    This makes me a bit nervous
    Post by: KRGraphicsCG, Jul 21, 2017 in forum: Troubleshooting
  15. KRGraphicsCG
    Post

    Bed Not Raising, Buzzing Sound

    A bent rod? I'm not the incredible hulk lol... and I looked very carefully in the build area and the threaded rod looks straight... I also set...
    Post by: KRGraphicsCG, Jul 21, 2017 in forum: Troubleshooting
  16. KRGraphicsCG
    Post

    Bed Not Raising, Buzzing Sound

    And I just got the printer too... I ran the machine this morning and the bed raised fine. It lowers fine too, just on occasion it will grind and...
    Post by: KRGraphicsCG, Jul 21, 2017 in forum: Troubleshooting
  17. KRGraphicsCG
    Post

    Bed Not Raising, Buzzing Sound

    I was able to run the Z Offset Wizard and now I have a new offset of -7.5 (it was -8 before). So I hope the grinding crap stops after this...
    Post by: KRGraphicsCG, Jul 20, 2017 in forum: Troubleshooting
  18. KRGraphicsCG
    Thread

    Bed Not Raising, Buzzing Sound

    So, on my 3rd day of printing... (I love the printer by the way, got some REALLY good prints off it.) I am trying to do a print and the bed makes...
    Thread by: KRGraphicsCG, Jul 20, 2017, 21 replies, in forum: Troubleshooting
  19. KRGraphicsCG
    Post

    Solved Unlevel bed....

    I am having some issues too with my print bed... when I set it to print it makes this buzzing noise which is kinda bothersome... I may have to...
    Post by: KRGraphicsCG, Jul 20, 2017 in forum: Troubleshooting
  20. KRGraphicsCG
    Post

    Two Spool Holders

    I was going to buy the Hatchbox spool holders, but with some rigid pvc, and some connectors, I can make my own :-)
    Post by: KRGraphicsCG, Jul 20, 2017 in forum: General Questions
Showing results 1 to 20 of 46 Next >
Search Again
Page 1 of 3