1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Suberman
    Post

    Unanswered Robo 3d R1 Plus

    This is my problem. Continuity is working. Any other advise? [MEDIA]
    Post by: Suberman, Jan 14, 2018 in forum: Troubleshooting
  2. Suberman
    Post

    Unanswered Robo 3d R1 Plus

    This is the switch that would be showing closed right?
    Post by: Suberman, Jan 14, 2018 in forum: Troubleshooting
  3. Suberman
    Post

    Unanswered Robo 3d R1 Plus

    It's possible but not likely. Why is it if i'm jogging the x+ or x- it works great only when i'm homing it before a print it goes the wrong way?...
    Post by: Suberman, Jan 14, 2018 in forum: Troubleshooting
  4. Suberman
    Thread

    Unanswered Robo 3d R1 Plus

    How do you know if you need to replace the driver stepper motor on the arduino board vs the servo motor? I have 2 different problems. I'm moving...
    Thread by: Suberman, Jan 14, 2018, 6 replies, in forum: Troubleshooting
  5. Suberman
    Post

    Unanswered Help with Matter Control

    I feel like i'm getting closer however i'm not sure what to do to get this right.
    Post by: Suberman, Jan 9, 2018 in forum: Troubleshooting
  6. Suberman
    Post

    Unanswered Help with Matter Control

    What program do you use to print?
    Post by: Suberman, Jan 9, 2018 in forum: Troubleshooting
  7. Suberman
    Post

    Unanswered Help with Matter Control

    After several prints and changes I think my best print is a layer height .25 Temp 205 & 210. I never could get the top of the pyramid to come out...
    Post by: Suberman, Jan 9, 2018 in forum: Troubleshooting
  8. Suberman
    Post

    Unanswered Help with Matter Control

    I will try different temperature setting. I will also move my layer height to .25. Its currently at .4. On the label reads diameter 1.75mm...
    Post by: Suberman, Jan 9, 2018 in forum: Troubleshooting
  9. Suberman
    Post

    Unanswered Help with Matter Control

    My tall prints are still coming out with no detail and now its stringy. How can I get a more detailed print when I print something tall? I'm...
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  10. Suberman
    Post

    Unanswered Help with Matter Control

    AMAZING!!! THANK YOU!! Its not perfect but its a better print at half the time. You just save half of my printer life :). Can you explain the...
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  11. Suberman
    Post

    Unanswered Help with Matter Control

    I'm not sure I understand. If you look at the screenshot it reads for layer height "The height of each layer of the print, except the first. A...
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  12. Suberman
    Post

    Unanswered Help with Matter Control

    This is a screenshot just in case you don't understand.
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  13. Suberman
    Post

    Unanswered Help with Matter Control

    What should my setting be? I like to use Matter Control 1.7 software. I have the infill set to .40 (Fill Density) infill type in set to grid....
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  14. Suberman
    Post

    Unanswered Help with Matter Control

    why is it when I change the EEProm i'm able to print? I'm having another problem that I would like some help with. I'm changing my fill density...
    Post by: Suberman, Jan 8, 2018 in forum: Troubleshooting
  15. Suberman
    Post

    Unanswered Help with Matter Control

    when it fails it just makes a noise like as if the z was trying to move and can't. the rods doesn't turn. let me know if you can't see the thumbnail
    Post by: Suberman, Dec 16, 2017 in forum: Troubleshooting
  16. Suberman
    Post

    Unanswered Help with Matter Control

    Robo R1
    Post by: Suberman, Dec 13, 2017 in forum: Troubleshooting
  17. Suberman
    Thread

    Unanswered Help with Matter Control

    I'm using Matter Control 1.7 and my Z axis will bind up making a loud noise when trying to home. If I change the options, hardware, EEProm,...
    Thread by: Suberman, Dec 12, 2017, 23 replies, in forum: Troubleshooting
  18. Suberman
    Post

    Answered Why did my print bed burn up?

    Is there any benefit to using connectors vs soldering the wires directly to each other? Do you have a diagram to show which wires go to which if...
    Post by: Suberman, Aug 22, 2017 in forum: Troubleshooting
  19. Suberman
    Post

    Answered Why did my print bed burn up?

    Can I just solder the wire together and print?
    Post by: Suberman, Aug 19, 2017 in forum: Troubleshooting
  20. Suberman
    Post

    Answered Why did my print bed burn up?

    Any advice on printing with the bed at room temp?
    Post by: Suberman, Aug 19, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 24 Next >
Search Again
Page 1 of 2