1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    Ordered! Thank you. Also do you know where to buy the wire connectors and 2 hole clip for the LED Lights and the metal connectors for the that...
    Post by: Michael Miller, Dec 8, 2017 in forum: Troubleshooting
  2. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    Thanks for the help. I was able to resoder the pins to the other setup. I was able to get it somewhat working again but I think the damage had...
    Post by: Michael Miller, Dec 8, 2017 in forum: Troubleshooting
  3. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    I will check when I get home tonight... I am not sure why it would be different? Thanks!
    Post by: Michael Miller, Dec 7, 2017 in forum: Troubleshooting
  4. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    I am little confused on this. I see pins to jumper between -/+ however I don't see them for the S. Am I missing something? There are holes on...
    Post by: Michael Miller, Dec 7, 2017 in forum: Troubleshooting
  5. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    Thank you for that! I will change them when I get home tonight and make sure they are correct.
    Post by: Michael Miller, Dec 7, 2017 in forum: Troubleshooting
  6. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    Would that cause that the end stops to stop working? How do I know which way is correct? Here are some closer pictures.
    Post by: Michael Miller, Dec 7, 2017 in forum: Troubleshooting
  7. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    Thank you mark. Here is the board I am using. The highlighted area is where I am hooking them up. I am making sure the red is on the positive...
    Post by: Michael Miller, Dec 7, 2017 in forum: Troubleshooting
  8. Michael Miller
    Thread

    Answered End Stops causing Arduino board not to work

    Hello! I have a Robo 3D R1. I was able to get it for free but I am having a hard time getting it connected. I looked at the wiring and I...
    Thread by: Michael Miller, Dec 7, 2017, 18 replies, in forum: Troubleshooting
  9. Michael Miller
    Post

    Unresolved Stringy Layers

    Here are some pictures of it when it fails...
    Post by: Michael Miller, Jun 28, 2016 in forum: Troubleshooting
  10. Michael Miller
    Post

    Unresolved Stringy Layers

    Here is a couple pictures of first layer... looks good.
    Post by: Michael Miller, Jun 28, 2016 in forum: Troubleshooting
  11. Michael Miller
    Post

    Unresolved Stringy Layers

    they were made back to back. I will try one with a hollow center.
    Post by: Michael Miller, Jun 28, 2016 in forum: Troubleshooting
  12. Michael Miller
    Post

    Unresolved Stringy Layers

    It seems like it is printing good but is almost skipping a layer when printing. I will try to get some video.
    Post by: Michael Miller, Jun 28, 2016 in forum: Troubleshooting
  13. Michael Miller
    Post

    Unresolved Stringy Layers

    I print this same model on other robo3d printers and they print perfectly.
    Post by: Michael Miller, Jun 28, 2016 in forum: Troubleshooting
  14. Michael Miller
    Thread

    Unresolved Stringy Layers

    I test printed a cube, cube and pyramid and all printed great to the correct dimesions. See the box in the picture below. The next picture is a...
    Thread by: Michael Miller, Jun 27, 2016, 10 replies, in forum: Troubleshooting
  15. Michael Miller
    Post

    Solved Not Printing Correctly after 1 mm

    Thank you! Works great now!!!
    Post by: Michael Miller, Jun 2, 2016 in forum: Troubleshooting
  16. Michael Miller
    Post

    Solved Not Printing Correctly after 1 mm

    When I try and update this is what I get in the audrino updater: Sketch uses 116,280 bytes (45%) of program storage space. Maximum is 253,952...
    Post by: Michael Miller, Jun 1, 2016 in forum: Troubleshooting
  17. Michael Miller
    Post

    Solved Not Printing Correctly after 1 mm

    It is a threaded rod. It has a coupler at the bottom. What firmware should I be using?
    Post by: Michael Miller, Jun 1, 2016 in forum: Troubleshooting
  18. Michael Miller
    Post

    Solved Not Printing Correctly after 1 mm

    It is a threaded rod. It has a coupler at the bottom.
    Post by: Michael Miller, Jun 1, 2016 in forum: Troubleshooting
  19. Michael Miller
    Post

    Solved Not Printing Correctly after 1 mm

    Post by: Michael Miller, Jun 1, 2016 in forum: Troubleshooting
  20. Michael Miller
    Post

    Solved Not Printing Correctly after 1 mm

    Here is my g-code. Am I missing something? G28 X0 Y0 Z0 ; home all axes G1 Z5 F5000 ; lift nozzle M109 S[temperature] ; set the extruder temp...
    Post by: Michael Miller, Jun 1, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 27 Next >
Search Again
Page 1 of 2