1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Answered Adhesion issues

Discussion in 'Troubleshooting' started by 3D Printer Man, May 21, 2016.

  1. 3D Printer Man

    Joined:
    May 21, 2016
    Messages:
    226
    Likes Received:
    57
    Hello,
    With my Robo R1 Plus, i am having addhesion issues. I have tried tape, glue, and hairspray. None of the stich to PLA.
     
    hi1 likes this.
  2. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,728
    Likes Received:
    2,328
    You'll need to look at your z offset and play withthatnumber until you find what works for your machine
     
  3. 3D Printer Man

    Joined:
    May 21, 2016
    Messages:
    226
    Likes Received:
    57
    But , how?
    I use mattercontrol!
     
    hi1 likes this.
  4. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,728
    Likes Received:
    2,328
    I don't use matter control but when I did there are big buttons that say offset I think on the main page, .8-1.1 I think. If your printing USB hit a smaller number to go closer then press print. I believe that's how you go about it for that slicer.
     
  5. mark tomlinson

    mark tomlinson ༼ つ ◕_ ◕ ༽つ
    Staff Member

    Joined:
    Feb 21, 2013
    Messages:
    23,421
    Likes Received:
    7,299
  6. 3D Printer Man

    Joined:
    May 21, 2016
    Messages:
    226
    Likes Received:
    57
    My heated bed just broke/cracked luckily on the side!
     
    hi1 likes this.
  7. GAmbrosio

    GAmbrosio Active Member

    Joined:
    Feb 22, 2016
    Messages:
    238
    Likes Received:
    79
    How did that happen?

    Geof and Mark,

    On this topic, with the LCD controller how do I set the Z offset? It starts at .50, won't go any lower...
     
  8. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,728
    Likes Received:
    2,328
    I dont know. I set mine through the start up script in s3d and havnt needed to adjust it on the fly.

    Why do you need/want to adjust through the controller ? Youve peaked my "im gna need this" bug lol
     
    GAmbrosio likes this.
  9. GAmbrosio

    GAmbrosio Active Member

    Joined:
    Feb 22, 2016
    Messages:
    238
    Likes Received:
    79
    The slicer passes this on, but then there are those "oh, s#13t moments where you see your filament dancing in the air...:)


    Sent from my iPhone using Tapatalk
     
  10. Geof

    Geof Volunteer Moderator
    Staff Member

    Joined:
    Nov 9, 2015
    Messages:
    6,728
    Likes Received:
    2,328
    I press stop print lol.typically when it does that to me it's an auto level switch out of whack so I know to check the auto level :). I know not an answer lol.
     
    GAmbrosio likes this.

Share This Page