1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Acclamator777

  1. Acclamator777
    Thread

    print not centered

    I just downloaded version 3.1 and my prints are starting at the front left of the bed and not center. Any thoughts to why this is happening
    Thread by: Acclamator777, Feb 28, 2018, 1 replies, in forum: Troubleshooting
  2. Acclamator777
    Thread

    CURA 3.1

    I just upgraded my cura software to the latest 3.1 version. I lost all my original G-code start up and end settings. Can somebody share your...
    Thread by: Acclamator777, Feb 22, 2018, 0 replies, in forum: Software
  3. Acclamator777
    Post

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    I added a belt tightener and it's printing great. Thanks you all for your help!
    Post by: Acclamator777, May 30, 2017 in forum: Troubleshooting
  4. Acclamator777
    Post

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    I replaced the stepper motor because it looked like the bearings were going out. I did a test print and all seemed ok.[ATTACH] I then tried the...
    Post by: Acclamator777, May 29, 2017 in forum: Troubleshooting
  5. Acclamator777
    Post

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    I will get to work on it! I will reply to let you know how things went and hopefully things will be working well. Thanks for the help!
    Post by: Acclamator777, May 29, 2017 in forum: Troubleshooting
  6. Acclamator777
    Post

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    Is it possible to replace the motor with one of the original Z axis motors I replaced with the lead screw upgrade kit? Or do I have to get a...
    Post by: Acclamator777, May 29, 2017 in forum: Troubleshooting
  7. Acclamator777
    Post

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    IBelt seems to be ok but I took a look at the motor and noticed that it looks like fluid in the bottom hole of the stepper motor [ATTACH] and...
    Post by: Acclamator777, May 29, 2017 in forum: Troubleshooting
  8. Acclamator777
    Thread

    Solved After Lead Screw Upgrade Installed, Layer Skip Occurs

    I just installed the lead screw upgrade kit on my refurbished R1. It prints out really good now. No more Z banding. But now I am encountering a...
    Thread by: Acclamator777, May 29, 2017, 11 replies, in forum: Troubleshooting
  9. Acclamator777
    Post

    Solved lead screw upgrade issues

    Having issues getting a video uploaded. Good news is I took a look at the stepper motor connections on the board underneath. I rotated the...
    Post by: Acclamator777, May 27, 2017 in forum: Troubleshooting
  10. Acclamator777
    Post

    Solved lead screw upgrade issues

    Sorry that it took so long to respond back. Here are pics of the left and right z switch lead screw upgrade assembly. Also, this is the...
    Post by: Acclamator777, May 25, 2017 in forum: Troubleshooting
  11. Acclamator777
    Post

    Solved lead screw upgrade issues

    Went to robo 3d firmware page and downloaded lead screw upgrade firmware.
    Post by: Acclamator777, May 25, 2017 in forum: Troubleshooting
  12. Acclamator777
    Thread

    Solved lead screw upgrade issues

    I have a refurbished R1 model and I just installed the lead screw upgrade. Pretty straight forward installation. I installed the lead screw...
    Thread by: Acclamator777, May 25, 2017, 10 replies, in forum: Troubleshooting