1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Adam Laird

  1. Adam Laird
    Post

    3rd Party App/Plugin Camera Access

    My issue with telegram was that the camera wasn’t turned on ‍♂️. It’s been fantastic since I figured that out. 10/10 would recommend. Setting up...
    Post by: Adam Laird, Jun 4, 2018 in forum: General Questions
  2. Adam Laird
    Thread

    3rd Party App/Plugin Camera Access

    Is there anyone using the telegram plugin on the R2? I’m not sure how to give it access to my camera so it can send me pictures of my prints. I’ve...
    Thread by: Adam Laird, May 13, 2018, 3 replies, in forum: General Questions
  3. Adam Laird
    Post

    Silicone Sock

    No problem! I got mine from PrintedSolid. They’ve got a lot of different e3d parts and part kits Sent from my iPhone using Tapatalk
    Post by: Adam Laird, Apr 14, 2018 in forum: General Questions
  4. Adam Laird
    Post

    Silicone Sock

    I ordered an e3d block and used the stock hexagon so I could put socks on it and that seemed to work ok until it leaked PETG everywhere... but I...
    Post by: Adam Laird, Apr 14, 2018 in forum: General Questions
  5. Adam Laird
    Post

    R2 Hood

    How did it turn out? I’m in the process of printing my first piece of it now. Sent from my iPhone using Tapatalk
    Post by: Adam Laird, Mar 29, 2018 in forum: Mods and Upgrades
  6. Adam Laird
    Post

    AstroPrint Plug-in with Octoprint?

    Thanks supercazzola! I really appreciate it, and all of your help and guidance on here. He sent me a pm on Facebook and I gave him the case ID...
    Post by: Adam Laird, Mar 11, 2018 in forum: Software
  7. Adam Laird
    Post

    E3D block with Robo Hexagon?

    It works! I had to trim the heat shrink on the thermistor cartridge to get it to fit far enough into the block, but it’s holding temp much more...
    Post by: Adam Laird, Mar 9, 2018 in forum: General Questions
  8. Adam Laird
    Post

    V2 Bed Buildtak Replacement

    The magnetic base has some cut outs in the corners. I think I read somewhere that they’re supposed to accommodate clips for beds on other...
    Post by: Adam Laird, Mar 9, 2018 in forum: General Questions
  9. Adam Laird
    Post

    BuildTac FlexPlate on V2 bed?

    Sorry! I’m new to the app and I didn’t realize that the link was routed through Tapatalk. Sent from my iPhone using Tapatalk
    Post by: Adam Laird, Mar 9, 2018 in forum: Mods and Upgrades
  10. Adam Laird
    Post

    V2 Bed Buildtak Replacement

    Thanks! I took the old buildtak off so there wasn’t any extra space between the heater and the surface. Being able to use the screws around the...
    Post by: Adam Laird, Mar 8, 2018 in forum: General Questions
  11. Adam Laird
    Post

    BuildTac FlexPlate on V2 bed?

    Here’s a link to another discussion about this. I posted pictures of the installed system on it! V2 Bed Buildtak Replacement...
    Post by: Adam Laird, Mar 8, 2018 in forum: Mods and Upgrades
  12. Adam Laird
    Post

    V2 Bed Buildtak Replacement

    I installed the 8.66 x8.66 FlexPlate! I’m trying to figure out temp settings for it now. I set it to 75 on the printer and the bed itself topped...
    Post by: Adam Laird, Mar 8, 2018 in forum: General Questions
  13. Adam Laird
    Thread

    AstroPrint Plug-in with Octoprint?

    Has anyone been using the AstroPrint plug in to remotely monitor your R2? I’ve been trying to get it running on my printer, but I need...
    Thread by: Adam Laird, Mar 7, 2018, 6 replies, in forum: Software