1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by BenJoeM

  1. BenJoeM
    Post

    Z-offset issue or slicer

    thanks. Recommendations on a slicer?
    Post by: BenJoeM, May 31, 2022 in forum: Troubleshooting
  2. BenJoeM
    Post

    Z-offset issue or slicer

    Here is one that I know works: ;FLAVOR:RepRap ;TIME:4640 ;Filament used: 4.92005m ;Layer height: 0.2 ;Generated with Cura_SteamEngine 2.5.0...
    Post by: BenJoeM, May 29, 2022 in forum: Troubleshooting
  3. BenJoeM
    Thread

    Z-offset issue or slicer

    i am slicing using CURA 2.5 the generic version that comes with the C2. recently when I send a file to print sliced via CURA either through the...
    Thread by: BenJoeM, May 28, 2022, 6 replies, in forum: Troubleshooting
  4. BenJoeM
    Post

    Z Off Set and Delay in Retraction of Extruder at the end

    yes, let me check
    Post by: BenJoeM, Aug 2, 2020 in forum: Troubleshooting
  5. BenJoeM
    Post

    Z Off Set and Delay in Retraction of Extruder at the end

    Thank you. I am using CURA, the original version that came with printer. I have not upgraded the software because when I’ve done in the past I...
    Post by: BenJoeM, Aug 2, 2020 in forum: Troubleshooting
  6. BenJoeM
    Thread

    Z Off Set and Delay in Retraction of Extruder at the end

    Hey, I have had my C2 for sometime and for some reason in the past few months I seem to struggle to get my Z OFF set correct. I do all the...
    Thread by: BenJoeM, Aug 1, 2020, 5 replies, in forum: Troubleshooting
  7. BenJoeM
    Post

    Solved Robo c2 extruder problem

    Tried making sure all sides were balanced, seemed to fix it once I did this.
    Post by: BenJoeM, Jun 2, 2020 in forum: Troubleshooting
  8. BenJoeM
    Thread

    Solved Robo c2 extruder problem

    Hey. Sudden issue. I’ve been printing just fine for weeks when suddenly my latest print the extruder on the right side wants to lift higher than...
    Thread by: BenJoeM, Jun 2, 2020, 3 replies, in forum: Troubleshooting
  9. BenJoeM
    Thread

    Feed Gear works perfectly with Robo C2 Files only

    So looking for some help here. I have now tested 4 filaments and 4 different prints off of the USB drive with. my C2 without issue. But as soon...
    Thread by: BenJoeM, Jun 15, 2018, 2 replies, in forum: Troubleshooting
  10. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Follow up to close this circle with you all! Thanks to @Geof and @mark tomlinson for your tremendous support as always. I purchased a new SD...
    Post by: BenJoeM, Jun 13, 2018 in forum: Troubleshooting
  11. BenJoeM
    Post

    Solved New C2 - Connection Interrupted error and New Image won't work!

    Correct, I get the blue robo screen then straigh to "UPDATING" and it could stay there for hours, I left it running for 4 hours once.
    Post by: BenJoeM, Jun 11, 2018 in forum: Troubleshooting