1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by bill Snyder

  1. bill Snyder
    Post

    How is everyone liking the R2

    ok. Clicked on buy it now and nothing went in the cart.
    Post by: bill Snyder, Sep 19, 2019 in forum: General Questions
  2. bill Snyder
    Post

    How is everyone liking the R2

    The R2 is up for sale on robo site. Wonder if this is false advertising lr what
    Post by: bill Snyder, Sep 18, 2019 in forum: General Questions
  3. bill Snyder
    Post

    R2 X AXIS

    wow what a project this has been. First stepper motor went out. Then while replacing with a Robo supplied stepper (in warrantee ) lost end...
    Post by: bill Snyder, Apr 22, 2019 in forum: Troubleshooting
  4. bill Snyder
    Post

    R2 X AXIS

    Thanks everyone. Ordered off amazon. it's 8mm id. 12mm od. it is a flanged bearing
    Post by: bill Snyder, Apr 5, 2019 in forum: Troubleshooting
  5. bill Snyder
    Post

    R2 X AXIS

    Received a replacement stepper from Robo. Replaced and works fine. Will upload images for replacement. BUT in loosening the axis I lost one of the...
    Post by: bill Snyder, Apr 4, 2019 in forum: Troubleshooting
  6. bill Snyder
    Post

    R2 X AXIS

    Put in a ticket to Robo and heard back from Jason. So they will be sending a new one. Just whether it's still in warrantee. Which it should be as...
    Post by: bill Snyder, Apr 1, 2019 in forum: Troubleshooting
  7. bill Snyder
    Post

    R2 X AXIS

    Ordered one on Amazon. Put in a ticket to Robo. This is my second ticket. First problem was nicely solved by Jason last month. Now to figure out...
    Post by: bill Snyder, Mar 30, 2019 in forum: Troubleshooting
  8. bill Snyder
    Post

    R2 X AXIS

    Thank you very much. Diagram really helped. Bill
    Post by: bill Snyder, Mar 30, 2019 in forum: Troubleshooting
  9. bill Snyder
    Post

    R2 X AXIS

    Thanks Guys. With the page Wheres Waldo provided they range from 38-42 mm. Plugs are varied. Some provide what each wire is. Voltage as low as...
    Post by: bill Snyder, Mar 30, 2019 in forum: Troubleshooting
  10. bill Snyder
    Post

    R2 X AXIS

    Thank you. Is there any instructions on replacement? I still have a month of warrantee. Is it worth waiting and going through Robo or just quicker...
    Post by: bill Snyder, Mar 29, 2019 in forum: Troubleshooting
  11. bill Snyder
    Post

    R2 X AXIS

    Seems the motor is froze. Machine is unplugged. Is there something I can do or do I have to replace? Thanks
    Post by: bill Snyder, Mar 28, 2019 in forum: Troubleshooting
  12. bill Snyder
    Post

    R2 X AXIS

    Thats my next step. Seems when all alen screws are loose on right side with large rod (bushing?) moves freely. When that rod is tighten it binds....
    Post by: bill Snyder, Mar 28, 2019 in forum: Troubleshooting
  13. bill Snyder
    Thread

    R2 X AXIS

    R2 Y axis moves freely. X axis very rough. Any thread dealing with this or solutions. Thanks
    Thread by: bill Snyder, Mar 28, 2019, 23 replies, in forum: Troubleshooting
  14. bill Snyder
    Post

    R2 with TGlase Clear

    yes i did.
    Post by: bill Snyder, Jan 31, 2019 in forum: Troubleshooting