1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by fredm

  1. fredm
    Post

    Is There A Firmware Upgrade for R1+

    there are no Hex files? wouldn't that be easier?
    Post by: fredm, Feb 25, 2019 in forum: General Questions
  2. fredm
    Post

    Is There A Firmware Upgrade for R1+

    where would I find marlin 1.1.9. I just did a search and this thread showed up.
    Post by: fredm, Feb 25, 2019 in forum: General Questions
  3. fredm
    Post

    Is There A Firmware Upgrade for R1+

    I was wondering about this also. My robo says V1 I downloaded form here it says V2...
    Post by: fredm, Feb 24, 2019 in forum: General Questions
  4. fredm
    Post

    Answered first layer not going down correctly?

    okay thanks I have a filament oiler but I always forget about it.
    Post by: fredm, Feb 3, 2019 in forum: Troubleshooting
  5. fredm
    Post

    Answered first layer not going down correctly?

    yes it was PLA. what do you mean "seasoned" can you recommend nozzles.? how bout these...
    Post by: fredm, Feb 3, 2019 in forum: Troubleshooting
  6. fredm
    Post

    Answered first layer not going down correctly?

    yeah I did that and it worked. also a couple other things: I was thinking maybe there was a bit of a clog that caused under extrusion also???? or...
    Post by: fredm, Feb 3, 2019 in forum: Troubleshooting
  7. fredm
    Thread

    Answered first layer not going down correctly?

    I dont know what happened. I never had this problem before. just printed a test support in matter controll. worked fine. I went to print another...
    Thread by: fredm, Feb 2, 2019, 7 replies, in forum: Troubleshooting
  8. fredm
    Post

    Solved SainSmart Flexible TPU-advice for first attemp

    thanks to everyone here that has helped me and answered my questions. it is a great resource.
    Post by: fredm, Jan 26, 2019 in forum: General Questions
  9. fredm
    Post

    Solved SainSmart Flexible TPU-advice for first attemp

    SUCCESS! at 15 mm/s 230C [MEDIA]
    Post by: fredm, Jan 25, 2019 in forum: General Questions
  10. fredm
    Post

    Solved SainSmart Flexible TPU-advice for first attemp

    yeah, I thought that was faster than 25mm/s. so I wasnt surprised to have a problem/ so I slowed it down to 15mm/s. and I had the same problem. I...
    Post by: fredm, Jan 25, 2019 in forum: General Questions
  11. fredm
    Post

    Solved SainSmart Flexible TPU-advice for first attemp

    first attempt was at 25 mm/s I thought this was going faster: [MEDIA]
    Post by: fredm, Jan 25, 2019 in forum: General Questions
  12. fredm
    Post

    Solved SainSmart Flexible TPU-advice for first attemp

    so I decided the try the bic pen method before breaking out the drill. it was going surprising well....until... the filament backed up in the...
    Post by: fredm, Jan 25, 2019 in forum: General Questions
  13. fredm
    Post

    Solved SainSmart Flexible TPU-advice for first attemp

    regarding drilling. I will be able to remove the tube to print as before without sacrificing performance?
    Post by: fredm, Jan 23, 2019 in forum: General Questions
  14. fredm
    Post

    Solved SainSmart Flexible TPU-advice for first attemp

    yikes, I just unscrewed the spring tensioned bolts. the hobbed bolt looks mighty close to the hole that need to be drilled. people have done this...
    Post by: fredm, Jan 23, 2019 in forum: General Questions