1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Gripp

  1. Gripp
    Post

    Partial Answer Hotend Turns off after autolevel

    I didn't get a chance to copy and past my s3d pronterface info. But I did go ahead and order a new thermistor. My E3D V6 uses the metal tube thing...
    Post by: Gripp, Aug 10, 2017 in forum: Troubleshooting
  2. Gripp
    Thread

    Partial Answer Hotend Turns off after autolevel

    I've been having an issue where by hot end seems to turn off after autolevel. I can get the print to run again, but I have to go to my lcd display...
    Thread by: Gripp, Aug 8, 2017, 9 replies, in forum: Troubleshooting
  3. Gripp
    Post

    Simplify3D

    Thanks for the GCode. Seemed to work (put in my own z-offest) for what I need. With the caveat that I preheat before I hit print. It started...
    Post by: Gripp, Jul 17, 2017 in forum: Software
  4. Gripp
    Thread

    Simplify3D

    So I broke down and bought a copy of S3D. I can't seem to get it to raise the z offset. I copied over my script from cura for starting and ending....
    Thread by: Gripp, Jul 15, 2017, 6 replies, in forum: Software
  5. Gripp
    Post

    Solved Extruder motor

    The gear came off, but the peg shape on the new motor only had one flat side, so I heated it with the hair dryer to get it on. Had to look into...
    Post by: Gripp, Jul 15, 2017 in forum: Troubleshooting
  6. Gripp
    Thread

    Solved Extruder motor

    So my extruder motor or motor cable seems to have went. The motor just clicks but doesn't fully turn, except on retraction. I bought a replacement...
    Thread by: Gripp, Jul 14, 2017, 3 replies, in forum: Troubleshooting
  7. Gripp
    Post

    Answered E3D V6 Loose on R1+

    Just changed these numbers and I'm about to do a test print. The defaults were 9000,9000,100,10000. That's quite the difference.
    Post by: Gripp, Jun 15, 2017 in forum: Troubleshooting
  8. Gripp
    Post

    Answered E3D V6 Loose on R1+

    Where in the firmware do I change this (config H?) and what is a good value to start with? I was printing that at like 45mm/s.
    Post by: Gripp, Jun 15, 2017 in forum: Troubleshooting
  9. Gripp
    Post

    Answered E3D V6 Loose on R1+

    It was the first link posted. I remember the white filament. I just put some electric tape around the collar and it's tight now. I'll look into...
    Post by: Gripp, Jun 15, 2017 in forum: Troubleshooting
  10. Gripp
    Post

    Answered E3D V6 Loose on R1+

    Cool. I'll check when I get home. Do you happen to know how high it should be?
    Post by: Gripp, Jun 12, 2017 in forum: Troubleshooting
  11. Gripp
    Post

    Answered E3D V6 Loose on R1+

    I don't recall off the top of my head, but it was a file for an e3d v6 quick release. Got it on thingiverse.
    Post by: Gripp, Jun 12, 2017 in forum: Troubleshooting
  12. Gripp
    Thread

    Answered E3D V6 Loose on R1+

    I installed a V6 this weekend and when I went to print, I noticed that the whole thing was loose. Loose in the way that you can grab the hot end...
    Thread by: Gripp, Jun 12, 2017, 19 replies, in forum: Troubleshooting