1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by ikre

  1. ikre
    Post

    Solved NOW extruder does not work!!!???

    Am i stupid or what....when warm it works......problem solved...
    Post by: ikre, Jun 27, 2016 in forum: Troubleshooting
  2. ikre
    Post

    Solved NOW extruder does not work!!!???

    Mark, yes i am trying to turn the extruder when it is cold. Normally it works (also when it is cold) If the powr supply is turned OFF i can turn...
    Post by: ikre, Jun 27, 2016 in forum: Troubleshooting
  3. ikre
    Thread

    Solved NOW extruder does not work!!!???

    OMG, i have made two prints that looked good. Now the steppemotor of the extruder does not work anymore. what i tsted was the following. 1. see...
    Thread by: ikre, Jun 27, 2016, 4 replies, in forum: Troubleshooting
  4. ikre
    Post

    Solved Z-axis end stop does not work anmore

    I FOUND THE PROBLEM!!!!!! i wanted to update the system after my first print this week....i used the wrong firmware.....flashed the R1 old...
    Post by: ikre, Jun 24, 2016 in forum: Troubleshooting
  5. ikre
    Post

    Solved Z-axis end stop does not work anmore

    aaah...thanks..... but this does not explain the problem of my current printer..
    Post by: ikre, Jun 23, 2016 in forum: Troubleshooting
  6. ikre
    Post

    Solved Z-axis end stop does not work anmore

    thanks for the comments and i already use the same end stop as in the link you posted...
    Post by: ikre, Jun 23, 2016 in forum: Troubleshooting
  7. ikre
    Post

    Solved Z-axis end stop does not work anmore

    I would gladly like to convert it to auto level, but have not researched HOW... Here are the pictures of the problem maker. [IMG] [IMG]
    Post by: ikre, Jun 23, 2016 in forum: Troubleshooting
  8. ikre
    Post

    Solved Z-axis end stop does not work anmore

    Started the software( i use the astrobox (software through raspberry pi) and tryed the controls. Now then i push UP the extruder goes up. When i...
    Post by: ikre, Jun 23, 2016 in forum: Troubleshooting
  9. ikre
    Post

    Solved Z-axis end stop does not work anmore

    Measured it ans switch works correctly.......next step.....looking at the software...
    Post by: ikre, Jun 23, 2016 in forum: Troubleshooting
  10. ikre
    Post

    Solved Z-axis end stop does not work anmore

    that is a good one......i jus tryed to get Mattercontrol up and running, but the printer gets connected but does not even respond...so i think...
    Post by: ikre, Jun 21, 2016 in forum: Troubleshooting
  11. ikre
    Post

    Solved Z-axis end stop does not work anmore

    I realy mean the Z axis indeed...i have already traced the wire to the mega board, but it is still connected. I will get my multimeter to see if...
    Post by: ikre, Jun 21, 2016 in forum: Troubleshooting
  12. ikre
    Post

    Solved Z-axis end stop does not work anmore

    I am working with the very first version Robo3D
    Post by: ikre, Jun 21, 2016 in forum: Troubleshooting
  13. ikre
    Thread

    Solved Z-axis end stop does not work anmore

    Hi there, i wanted to see if the printer was stil calibrated, so i wanted to home everything. I now see that the y-ax end stop does not work....
    Thread by: ikre, Jun 20, 2016, 21 replies, in forum: Troubleshooting