1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by JeffL

  1. JeffL
    Post

    Partial Answer Another clogged hot end question... desperate user

    I ordered a couple options on Amazon. Hopefully will get things running.
    Post by: JeffL, Dec 11, 2018 in forum: Troubleshooting
  2. JeffL
    Post

    Partial Answer Another clogged hot end question... desperate user

    I need to get this running by this weekend... I need to find a hot end on Amazon. I am not going by pay robo3d for another replacement and have to...
    Post by: JeffL, Dec 11, 2018 in forum: Troubleshooting
  3. JeffL
    Post

    Partial Answer Another clogged hot end question... desperate user

    Ya. That was my 3rd resistor. I bought one from a parts store, then one came with the hot end from robo3d hot end that cost me 75 and the one from...
    Post by: JeffL, Dec 11, 2018 in forum: Troubleshooting
  4. JeffL
    Post

    Partial Answer Another clogged hot end question... desperate user

    well i am done... i broke the the thermistor wire trying to clean out another clog... tired of this piece of garbage...
    Post by: JeffL, Dec 11, 2018 in forum: Troubleshooting
  5. JeffL
    Post

    Partial Answer Another clogged hot end question... desperate user

    I don't have the exact message but I have seen something about "Temperature fell too much during print!" I have a new fan coming that cools the...
    Post by: JeffL, Dec 11, 2018 in forum: Troubleshooting
  6. JeffL
    Post

    Partial Answer Another clogged hot end question... desperate user

    i am tired of this printer... was great... now it is complete GARBAGE... i cant figure it out... i spend hours unclogging it and then it starts to...
    Post by: JeffL, Dec 10, 2018 in forum: Troubleshooting
  7. JeffL
    Thread

    Answered why is this doing this? i am so frustrated...

    i already spent 8+ hours trying to get the hot end unclogged... wasted 75 dollars because I broke the hotend I just got from Robo3d... i am not...
    Thread by: JeffL, Dec 10, 2018, 2 replies, in forum: Troubleshooting
  8. JeffL
    Post

    Partial Answer Another clogged hot end question... desperate user

    roger that. i will try and post back.
    Post by: JeffL, Dec 10, 2018 in forum: Troubleshooting
  9. JeffL
    Post

    Partial Answer Another clogged hot end question... desperate user

    I have reviewed and followed the sticky thread that is how I got the printer operational again. However I can't figure out why it keeps...
    Post by: JeffL, Dec 10, 2018 in forum: Troubleshooting
  10. JeffL
    Thread

    Partial Answer Another clogged hot end question... desperate user

    I have had my Robo 3D R1 for a couple years and the last couple months have been nothing but one challenge after another. The hot end just...
    Thread by: JeffL, Dec 10, 2018, 18 replies, in forum: Troubleshooting
  11. JeffL
    Post

    Solved New Robo3D does not reset to home - Z axis just goes up

    i took the top arch off and put the left and right arms back into position. see before and after pics Before [ATTACH] After[ATTACH]
    Post by: JeffL, Feb 5, 2016 in forum: Troubleshooting
  12. JeffL
    Thread

    Solved New Robo3D does not reset to home - Z axis just goes up

    I just got in my robo3d plus and set it up and installed the software and updated the software MatterControl to 1.4. I installed all the drivers...
    Thread by: JeffL, Feb 4, 2016, 6 replies, in forum: Troubleshooting