1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by JoshYourITGuy

  1. JoshYourITGuy
    Post

    S3D V4 Variable Settings Wont Send Temp Changes?

    Yes, let me clear the whole thing out and reload the model and re-split it.
    Post by: JoshYourITGuy, Sep 1, 2017 in forum: Software
  2. JoshYourITGuy
    Post

    S3D V4 Variable Settings Wont Send Temp Changes?

    Yes, I went through each process and modified the temp, but it is not reflected in the GCODE. For now, I just manually edited the GCODE by adding...
    Post by: JoshYourITGuy, Sep 1, 2017 in forum: Software
  3. JoshYourITGuy
    Thread

    S3D V4 Variable Settings Wont Send Temp Changes?

    Simplify3D, V4 I am trying to do a temp tower to play with an off-brand HIPS to see what temp it likes. Used the Variable Settings Wizard, I have...
    Thread by: JoshYourITGuy, Aug 31, 2017, 5 replies, in forum: Software
  4. JoshYourITGuy
    Post

    Solved Print Bed "Upgrade"

    Columbus OH had 1 when I sent you that link this morning, but looks like it is sold out now?
    Post by: JoshYourITGuy, Aug 2, 2017 in forum: General Questions
  5. JoshYourITGuy
    Post

    Solved Print Bed "Upgrade"

    My local MicroCenter has them, so thats a bummer for your location :( Install was easy (minus finding a cracked Y-Axis end and having to print a...
    Post by: JoshYourITGuy, Aug 2, 2017 in forum: General Questions
  6. JoshYourITGuy
    Post

    Solved Print Bed "Upgrade"

    http://www.microcenter.com/product/472738/Magnetic_Base_and_High_Temperature_Build_Plate
    Post by: JoshYourITGuy, Aug 2, 2017 in forum: General Questions
  7. JoshYourITGuy
    Thread

    Possible to add failsafe to SSR?

    I bought a GeckoTek magnetic base and plate system after I chipped yet another glass bed. (Thank you Polymax PLA) The GeckoTek system has a much...
    Thread by: JoshYourITGuy, May 22, 2017, 2 replies, in forum: Mods and Upgrades
  8. JoshYourITGuy
    Post

    Unresolved Volcano wobbles

    I will have to investigate that plate. I was thinking it was about time to replace those screws anyway, the hex sockets were getting rounded a...
    Post by: JoshYourITGuy, May 18, 2017 in forum: Troubleshooting
  9. JoshYourITGuy
    Post

    Unresolved Volcano wobbles

    Looks like it is from inside the Greg's Wade, last time I pulled the hot-end, I could see the thread-bite area was a bit "wollered" so I rotated...
    Post by: JoshYourITGuy, May 18, 2017 in forum: Troubleshooting
  10. JoshYourITGuy
    Thread

    Unresolved Volcano wobbles

    I am having an issue with my Volcano add-on. Due to the added length, there is a noticeable wobble of about 1-2mm at the nozzle during a print,...
    Thread by: JoshYourITGuy, May 18, 2017, 8 replies, in forum: Troubleshooting
  11. JoshYourITGuy
    Post

    Drying filament

    Could you just crank the temp and run the power cord through a PID controller for a more accurate temp?
    Post by: JoshYourITGuy, May 18, 2017 in forum: Projects
  12. JoshYourITGuy
    Post

    PLA Looking for a comparable to Hatchbox neon yellow filament

    Check for Inland brand on amazon (or MicroCenter if you have one locally) under $20 a spool and just as good as HatchBox
    Post by: JoshYourITGuy, May 18, 2017 in forum: Printing Filament