1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by KenO

  1. KenO
    Post

    Test your printers clearance and tolerance by Maker's Muse

    Sorry for the late response. I did this a couple years ago when my R2 was new. I checked out Angus of Maker's Muse this morning and I see that...
    Post by: KenO, Apr 4, 2020 in forum: Show and Tell
  2. KenO
    Post

    The Filament Reel Support Mod For C2 and R2 printers

    I have only sprayed the spool holder twice. I did not wipe it off. Note that I just started using the teflon spray for the last three or four TPU...
    Post by: KenO, Mar 27, 2020 in forum: Mods and Upgrades
  3. KenO
    Post

    The Filament Reel Support Mod For C2 and R2 printers

    Another solution to this problem I solved by using Dry Lube with Teflon. I sprayed the inside of the spool and the spool arm on the printer and I...
    Post by: KenO, Mar 26, 2020 in forum: Mods and Upgrades
  4. KenO
    Post

    The Filament Reel Support Mod For C2 and R2 printers

    Post by: KenO, Mar 26, 2020 in forum: Mods and Upgrades
  5. KenO
    Post

    Palette 2/Palette 2 Pro

    Tkoco, I responded to your email and said that that would be fine. Probably more easily located if it was there. Ken
    Post by: KenO, Feb 7, 2020 in forum: Projects
  6. KenO
    Post

    Palette 2/Palette 2 Pro

    Preamble on how I was able to get the Mosaic Palette 2 up and working. Note that I have tried hard to make it understandable. I am not very good...
    Post by: KenO, Jan 31, 2020 in forum: Projects
  7. KenO
    Post

    Palette 2/Palette 2 Pro

    I have the instructions almost complete. Still proof reading them. However, the following is just a check to see if a cut and paste link works:...
    Post by: KenO, Jan 31, 2020 in forum: Projects
  8. KenO
    Post

    Palette 2/Palette 2 Pro

    Give me a couple of days to put it all together. Ken
    Post by: KenO, Jan 29, 2020 in forum: Projects
  9. KenO
    Post

    Palette 2/Palette 2 Pro

    I finally got the my Palette 2S to work. I used Cura 2.5.0 that Robo provided when I purchased the R2 to access Octopi. After assuring myself that...
    Post by: KenO, Jan 28, 2020 in forum: Projects
  10. KenO
    Post

    Palette 2/Palette 2 Pro

    Alien or ?: finally got the palette to run and start a print, but how do you jog the filament when it asks you to load? That function is not...
    Post by: KenO, Jan 28, 2020 in forum: Projects
  11. KenO
    Post

    Palette 2 Pro Setup Experience

    The idea of linking two Raspberry Pi's together was not intended. It was to simply to locate a 2nd Raspberry Pi above the other, but only one of...
    Post by: KenO, Jan 18, 2020 in forum: General Questions
  12. KenO
    Post

    Palette 2 Pro Setup Experience

    OK, there is so many bits and pieces of info on how to get the Palette to work, that this is good info. I did make a duplicate SD card and saved...
    Post by: KenO, Jan 17, 2020 in forum: General Questions
  13. KenO
    Post

    Palette 2 Pro Setup Experience

    Partsbuild 3d sells a replacement Raspberry Pi for the Robo C1/C2's. Rather than re-program the existing Raspberry Pi, mount a replacement on a 3d...
    Post by: KenO, Jan 17, 2020 in forum: General Questions
  14. KenO
    Post

    PALATTE 2 USERS?

    What file format would you be starting with that you want to create the STL file from?
    Post by: KenO, Jan 13, 2020 in forum: General Questions
  15. KenO
    Post

    Palette 2/Palette 2 Pro

    I just noted that this link from Mosaic:...
    Post by: KenO, Jan 10, 2020 in forum: Projects