1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by MChrisP1

  1. MChrisP1
    Post

    Community Favorite Marlin 1.1.7 Release for Robo R1, R1+PLUS & Variants

    Don - looking good! On that corner with thinning you may need to 'cheat/compensate' for what you see with those results when doing mesh setting in...
    Post by: MChrisP1, Aug 6, 2017 in forum: Mods and Upgrades
  2. MChrisP1
    Post

    Converting C2 into the FT-5

    Dustin Corbin has a piece on YouTube for adjusting voltage in steppers. Sent from my iPhone using Tapatalk
    Post by: MChrisP1, Jun 8, 2017 in forum: Mods and Upgrades
  3. MChrisP1
    Post

    Converting C2 into the FT-5

    I figure it's all about what the Robo board will handle. My guess/hunch is it should be fine. Like Geof stated above, make sure your drives have...
    Post by: MChrisP1, Jun 8, 2017 in forum: Mods and Upgrades
  4. MChrisP1
    Post

    Interesting observation about hairspray

    Crazy! Sounds like it all congealed into a single mass and slid off? Sent from my iPhone using Tapatalk
    Post by: MChrisP1, Jun 5, 2017 in forum: Off Topic
  5. MChrisP1
    Post

    DIY FDM printer

    So far I'm liking the FT5. Im getting ready to stretch its legs here coming up. In the next month I'll have a solid opinion. I've added the 713...
    Post by: MChrisP1, May 23, 2017 in forum: Off Topic
  6. MChrisP1
    Post

    Anyone want to participate in a group print!

    [IMG][IMG] Sent from my iPhone using Tapatalk
    Post by: MChrisP1, Apr 9, 2017 in forum: Off Topic
  7. MChrisP1
    Post

    C2 LCD Controller modification for the Beta/R1/R1+

    You guys are master Robo hackers!!! Great work guys! Amazing to watch. Sent from my iPhone using Tapatalk
    Post by: MChrisP1, Mar 29, 2017 in forum: Projects
  8. MChrisP1
    Post

    Heater Upgrade Question

    Toro - May Inquires as to what you finally ended up doing for your setup? What did you use for the new bed heater and did you use the power supply...
    Post by: MChrisP1, Dec 11, 2016 in forum: Mods and Upgrades
  9. MChrisP1
    Post

    A couple of questions on build plates...

    Did you get the 10x10 fleks3d system? Sent from my iPhone using Tapatalk
    Post by: MChrisP1, Jun 16, 2016 in forum: General Questions
  10. MChrisP1
    Post

    A couple of questions on build plates...

    Can you show a screenshot of your script? I bet somebody here can debug it. Sent from my iPhone using Tapatalk
    Post by: MChrisP1, May 25, 2016 in forum: General Questions
  11. MChrisP1
    Post

    Printed Solid Store Grand Opening!

    Matt - Your event was great! Ill be back!
    Post by: MChrisP1, May 25, 2016 in forum: Off Topic
  12. MChrisP1
    Post

    A couple of questions on build plates...

    Thank you Geof! Lots of great info! Sent from my iPhone using Tapatalk
    Post by: MChrisP1, May 24, 2016 in forum: General Questions
  13. MChrisP1
    Thread

    A couple of questions on build plates...

    I have a couple of questions about the Robo3D build plate and that new Fleks system people are using. Some background, I'm new around here, just...
    Thread by: MChrisP1, May 24, 2016, 16 replies, in forum: General Questions
  14. MChrisP1
    Post

    Hi from SC!

    Welcome from Maryland Kristin! This is a good group, and as Waldo states, very helpful. I'm about a month into this as well. Happy printing!...
    Post by: MChrisP1, Apr 10, 2016 in forum: United States of America