1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Michael Miller

  1. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    Ordered! Thank you. Also do you know where to buy the wire connectors and 2 hole clip for the LED Lights and the metal connectors for the that...
    Post by: Michael Miller, Dec 8, 2017 in forum: Troubleshooting
  2. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    Thanks for the help. I was able to resoder the pins to the other setup. I was able to get it somewhat working again but I think the damage had...
    Post by: Michael Miller, Dec 8, 2017 in forum: Troubleshooting
  3. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    I will check when I get home tonight... I am not sure why it would be different? Thanks!
    Post by: Michael Miller, Dec 7, 2017 in forum: Troubleshooting
  4. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    I am little confused on this. I see pins to jumper between -/+ however I don't see them for the S. Am I missing something? There are holes on...
    Post by: Michael Miller, Dec 7, 2017 in forum: Troubleshooting
  5. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    Thank you for that! I will change them when I get home tonight and make sure they are correct.
    Post by: Michael Miller, Dec 7, 2017 in forum: Troubleshooting
  6. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    Would that cause that the end stops to stop working? How do I know which way is correct? Here are some closer pictures.
    Post by: Michael Miller, Dec 7, 2017 in forum: Troubleshooting
  7. Michael Miller
    Post

    Answered End Stops causing Arduino board not to work

    Thank you mark. Here is the board I am using. The highlighted area is where I am hooking them up. I am making sure the red is on the positive...
    Post by: Michael Miller, Dec 7, 2017 in forum: Troubleshooting
  8. Michael Miller
    Thread

    Answered End Stops causing Arduino board not to work

    Hello! I have a Robo 3D R1. I was able to get it for free but I am having a hard time getting it connected. I looked at the wiring and I...
    Thread by: Michael Miller, Dec 7, 2017, 18 replies, in forum: Troubleshooting
  9. Michael Miller
    Post

    Unresolved Stringy Layers

    Here are some pictures of it when it fails...
    Post by: Michael Miller, Jun 28, 2016 in forum: Troubleshooting
  10. Michael Miller
    Post

    Unresolved Stringy Layers

    Here is a couple pictures of first layer... looks good.
    Post by: Michael Miller, Jun 28, 2016 in forum: Troubleshooting
  11. Michael Miller
    Post

    Unresolved Stringy Layers

    they were made back to back. I will try one with a hollow center.
    Post by: Michael Miller, Jun 28, 2016 in forum: Troubleshooting
  12. Michael Miller
    Post

    Unresolved Stringy Layers

    It seems like it is printing good but is almost skipping a layer when printing. I will try to get some video.
    Post by: Michael Miller, Jun 28, 2016 in forum: Troubleshooting
  13. Michael Miller
    Post

    Unresolved Stringy Layers

    I print this same model on other robo3d printers and they print perfectly.
    Post by: Michael Miller, Jun 28, 2016 in forum: Troubleshooting
  14. Michael Miller
    Post

    Unresolved Stringy Layers

    I test printed a cube, cube and pyramid and all printed great to the correct dimesions. See the box in the picture below. The next picture is a...
    Post by: Michael Miller, Jun 27, 2016 in forum: Troubleshooting