1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by mike aguilar

  1. mike aguilar
    Post

    Answered First layer of PLA wont stick

    Thanks Mark I will give that a shot and let you know later.
    Post by: mike aguilar, Aug 19, 2017 in forum: Troubleshooting
  2. mike aguilar
    Thread

    Answered First layer of PLA wont stick

    Heya Guys Im sure I posted this before but not a forum junkie here, I got myself another R13D printer but this one is not laying a layer down to...
    Thread by: mike aguilar, Aug 19, 2017, 3 replies, in forum: Troubleshooting
  3. mike aguilar
    Post

    Solved Another Jam / Clog new R1 plus

    After assembling and running I believe "these violent delights have violent ends" came out good Thanks Mark again for your time! [ATTACH]
    Post by: mike aguilar, Jan 21, 2017 in forum: Troubleshooting
  4. mike aguilar
    Post

    Solved Another Jam / Clog new R1 plus

    Thank you Mark much appreciated on ur time let's hope I'm back to printing soon
    Post by: mike aguilar, Jan 21, 2017 in forum: Troubleshooting
  5. mike aguilar
    Post

    Solved Another Jam / Clog new R1 plus

    I got it cleared I boiled it in water cleaned it out good and used air can on it reassembling right now
    Post by: mike aguilar, Jan 21, 2017 in forum: Troubleshooting
  6. mike aguilar
    Post

    Solved Another Jam / Clog new R1 plus

    Ok it's off but still stuck in there good any recommendations? [ATTACH]
    Post by: mike aguilar, Jan 21, 2017 in forum: Troubleshooting
  7. mike aguilar
    Post

    Solved Another Jam / Clog new R1 plus

    Thank you Mark I will give it a shot and see
    Post by: mike aguilar, Jan 21, 2017 in forum: Troubleshooting
  8. mike aguilar
    Thread

    Solved Another Jam / Clog new R1 plus

    I'm at my wits end here in pic I have same issue l, filament stuck in hotend and will not come out this seems to be jammed clogged whatever temp...
    Thread by: mike aguilar, Jan 21, 2017, 10 replies, in forum: Troubleshooting
  9. mike aguilar
    Post

    Unresolved Extruder wont release filament after heating up

    Thanks guys I will look into this as well as seeing if this fixes. Much appreciated !
    Post by: mike aguilar, May 4, 2016 in forum: Troubleshooting
  10. mike aguilar
    Post

    Unresolved Extruder wont release filament after heating up

    Havent used a oiler yet im sure that will add ease to it or help this issue from happening again.
    Post by: mike aguilar, May 4, 2016 in forum: Troubleshooting
  11. mike aguilar
    Post

    Unresolved Extruder wont release filament after heating up

    Ok thanks for replying it's a robo 3D plus I usually heat it up to 210 to run. I load it around 185 as it says on printer. Anymore info needed...
    Post by: mike aguilar, May 3, 2016 in forum: Troubleshooting
  12. mike aguilar
    Thread

    Unresolved Extruder wont release filament after heating up

    Ok I took a break from printing things for awhile as I finished a Fallout clock for my daughter. It was cool and I was happy and she loved it. The...
    Thread by: mike aguilar, May 3, 2016, 7 replies, in forum: Troubleshooting