1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Sefa

  1. Sefa
    Post

    New Update brought back leveling issue

    @AllenMcAfee I contacted Robo support via email and they told me this: "Thanks for the video, it shows the tape you have on the bed and I think...
    Post by: Sefa, Mar 17, 2018 in forum: Troubleshooting
  2. Sefa
    Post

    New Update brought back leveling issue

    @AllenMcAfee I am sorry for the confusion, here it is: Send: M501 Recv: echo:V41 stored settings retrieved (498 bytes; crc 23950) Recv: echo: G21...
    Post by: Sefa, Mar 16, 2018 in forum: Troubleshooting
  3. Sefa
    Post

    New Update brought back leveling issue

    @AllenMcAfee Thank you for your response. When I enter M501 into the terminal, I get this: Send: M105 Recv: ok T:18.75 /0.00 B:21.56 /0.00 @:0...
    Post by: Sefa, Mar 14, 2018 in forum: Troubleshooting
  4. Sefa
    Post

    New Update brought back leveling issue

    Now it is every time. The support sent me this update about 2-3 months ago when they were testing, it did the same and I had to downgrade my...
    Post by: Sefa, Mar 13, 2018 in forum: Troubleshooting
  5. Sefa
    Thread

    New Update brought back leveling issue

    Hi everyone, I used to have autoleveling problem, got an IR replacement which seemed to fix my issue for a while. Now I just got the update...
    Thread by: Sefa, Mar 12, 2018, 16 replies, in forum: Troubleshooting
  6. Sefa
    Post

    Bed, Extruder, IR Sensor replaced yet my issues are not over

    I put the green painter's tape on because of my previous issue where my nozzle used to hit the bed resulting in damages and burns in the bed. Robo...
    Post by: Sefa, Jan 12, 2018 in forum: Troubleshooting
  7. Sefa
    Post

    Bed, Extruder, IR Sensor replaced yet my issues are not over

    I had the same issue in the summer a couple of times, I was printing at 230 degrees. It may be the filament, I will try with another filament.
    Post by: Sefa, Jan 7, 2018 in forum: Troubleshooting
  8. Sefa
    Post

    Bed, Extruder, IR Sensor replaced yet my issues are not over

    My bad, the photos were private, moved them to a public host.
    Post by: Sefa, Jan 6, 2018 in forum: Troubleshooting
  9. Sefa
    Post

    Bed, Extruder, IR Sensor replaced yet my issues are not over

    Hi all, I removed the philips screw and when that plastic part is not on the bearing on the right, it seemed to be working. So I will not put the...
    Post by: Sefa, Jan 5, 2018 in forum: Troubleshooting
  10. Sefa
    Post

    Bed, Extruder, IR Sensor replaced yet my issues are not over

    Here is a video of the issue, you can also see my last print attempt in the end. [MEDIA] And here is the photos Hobb gear used to be loose...
    Post by: Sefa, Jan 2, 2018 in forum: Troubleshooting
  11. Sefa
    Post

    Bed, Extruder, IR Sensor replaced yet my issues are not over

    It is 1.75mm Repkord filament. I tried with other filaments too.
    Post by: Sefa, Jan 1, 2018 in forum: Troubleshooting
  12. Sefa
    Post

    Bed, Extruder, IR Sensor replaced yet my issues are not over

    Hi all, Thanks for your support, after long talks with Robo support. Yet, I have another issue. The printer is not able to roll the filament in...
    Post by: Sefa, Jan 1, 2018 in forum: Troubleshooting
  13. Sefa
    Post

    Bed, Extruder, IR Sensor replaced yet my issues are not over

    Hi, I just received a new uptown adapter from Robo, they thought it was the problem. I changed it however, it is the same thing. I get the error...
    Post by: Sefa, Nov 28, 2017 in forum: Troubleshooting
  14. Sefa
    Post

    Bed, Extruder, IR Sensor replaced yet my issues are not over

    Hi all, I am sorry that I opened the thread in the wrong place. Yes, it is an R2. I am on the phone with Robo staff now, we fixed the gcodes,...
    Post by: Sefa, Nov 22, 2017 in forum: Troubleshooting