1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by Steven A. Berneberg

  1. Steven A. Berneberg
    Post

    Answered Printer sending emails?

    Mark: Sorry but I have no idea what OctoPrint is. I am using MatterControl.
    Post by: Steven A. Berneberg, Mar 19, 2018 in forum: Troubleshooting
  2. Steven A. Berneberg
    Thread

    Answered Printer sending emails?

    My email server has been shut down by my ISP because there have been too many rejected emails. It appears that someone somewhere is sending...
    Thread by: Steven A. Berneberg, Mar 19, 2018, 3 replies, in forum: Troubleshooting
  3. Steven A. Berneberg
    Post

    Solved Hot end fan-questions

    The fan has been replaced. Just spliced in the old connector since the new ones have not arrived yet. The first print, while small is OK. The...
    Post by: Steven A. Berneberg, Jan 22, 2018 in forum: Troubleshooting
  4. Steven A. Berneberg
    Post

    Solved Hot end fan-questions

    Thanks everyone for the input. I have ordered three fans since they seem to be a weak point. I have also ordered connectors but they will not be...
    Post by: Steven A. Berneberg, Jan 19, 2018 in forum: Troubleshooting
  5. Steven A. Berneberg
    Post

    Solved Hot end fan-questions

    Fan connectors: Part number SMR-O2V-B (Black) or SMR-02V-N (Natural). The socket contact appears to be SHF-OO1T-0.8BS. You will need a special...
    Post by: Steven A. Berneberg, Jan 15, 2018 in forum: Troubleshooting
  6. Steven A. Berneberg
    Post

    Solved Hot end fan-questions

    OK, the fan is bad. Took it out and ran it on the bench. Draws 0.2A, specification is 0.1A. However, if I lay the fan flat, it runs faster and...
    Post by: Steven A. Berneberg, Jan 15, 2018 in forum: Troubleshooting
  7. Steven A. Berneberg
    Post

    Solved Hot end fan-questions

    Thanks. The JST web site would not allow me to search for JST-SM. I had to look it up by alpha's....found it. Thanks.
    Post by: Steven A. Berneberg, Jan 15, 2018 in forum: Troubleshooting
  8. Steven A. Berneberg
    Post

    Solved Hot end fan-questions

    Just got through spending an hour looking at the JST web site for wire to wire connectors and did not find anything.
    Post by: Steven A. Berneberg, Jan 15, 2018 in forum: Troubleshooting
  9. Steven A. Berneberg
    Post

    Solved Hot end fan-questions

    Yeah, the problem here it appears as if they did not leave any service loop in the cable bundle. I doubt that I will be able to change the...
    Post by: Steven A. Berneberg, Jan 15, 2018 in forum: Troubleshooting
  10. Steven A. Berneberg
    Thread

    Solved Hot end fan-questions

    After much troubleshooting of stuck filament in my R1+ and reading many of the comments posted, I have determined that my Hot End Fan is not doing...
    Thread by: Steven A. Berneberg, Jan 15, 2018, 12 replies, in forum: Troubleshooting
  11. Steven A. Berneberg
    Post

    Unresolved MatterControl has stopped working

    Found the problem. Someone, somewhere suggested deleting the file ../users/appdata/mattercontrol. At least I think that was the link. Deleted...
    Post by: Steven A. Berneberg, Jan 17, 2017 in forum: Troubleshooting
  12. Steven A. Berneberg
    Thread

    Unresolved MatterControl has stopped working

    For some reason MatterControl is no longer launching. I get the window "MatterControl has stopped working" and get the following: Problem...
    Thread by: Steven A. Berneberg, Jan 17, 2017, 2 replies, in forum: Troubleshooting