1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!

Recent Content by studiver13

  1. studiver13
    Post

    Connection Interrupted

    its alive!!! https://imgur.com/rFupl2p thank you all for the help!
    Post by: studiver13, Dec 26, 2019 in forum: Troubleshooting
  2. studiver13
    Post

    Connection Interrupted

    I was able to get to the drive by following this post: http://community.robo3d.com/index.php?threads/robo-c2-image-download-link.17955/ I then...
    Post by: studiver13, Dec 26, 2019 in forum: Troubleshooting
  3. studiver13
    Post

    Connection Interrupted

    It appears the above link only shares the file, not the location. Whenever the R2 file is loaded, can you paste that link? Thanks!
    Post by: studiver13, Dec 24, 2019 in forum: Troubleshooting
  4. studiver13
    Post

    Connection Interrupted

    It would need to be the newer R2, not C2. I was attempting to go through updates to pull the latest info, but the printer loads an update screen...
    Post by: studiver13, Dec 24, 2019 in forum: Troubleshooting
  5. studiver13
    Post

    Connection Interrupted

    Would I need to follow the same instructions that are here: http://community.robo3d.com/index.php?threads/os-corrupted-in-update.19315/ in order...
    Post by: studiver13, Dec 24, 2019 in forum: Troubleshooting
  6. studiver13
    Post

    Connection Interrupted

    Re downloaded and flashed the firmware, still get the same issue. When I home it, the bed drops to the bottom and the extruder goes to the back...
    Post by: studiver13, Dec 24, 2019 in forum: Troubleshooting
  7. studiver13
    Post

    Connection Interrupted

    2.0.0-r2.6
    Post by: studiver13, Dec 24, 2019 in forum: Troubleshooting
  8. studiver13
    Post

    Connection Interrupted

    I am not making it far enough for that to happen. The robo screen is sitting on step 1/4 and the terminal is printing "wait" over and over again....
    Post by: studiver13, Dec 24, 2019 in forum: Troubleshooting
  9. studiver13
    Post

    Connection Interrupted

    I tried resetting the factory defaults. I even recompiled the .hex file and re flashed it, just in case it was the C2 profile. I still get the...
    Post by: studiver13, Dec 24, 2019 in forum: Troubleshooting
  10. studiver13
    Post

    Connection Interrupted

    I initially used Marlin_1.1.6_RoboVersion_1.2.4 with the arduino IDE and then I flashed Marlin_1.1.6_RoboVersion_1.2.6_R2.hex using the firmware...
    Post by: studiver13, Dec 24, 2019 in forum: Troubleshooting
  11. studiver13
    Post

    Connection Interrupted

    Thanks for all the help and tips! Good news, I flashed the firmware and the printer was able to connect again. Turns out I also had the Y axis...
    Post by: studiver13, Dec 23, 2019 in forum: Troubleshooting
  12. studiver13
    Post

    Connection Interrupted

    It appears then I do have V2. And the "rusty" parts on the actual bed connection pins. Based on some of the robo guides, most of them have the V1...
    Post by: studiver13, Dec 23, 2019 in forum: Troubleshooting
  13. studiver13
    Post

    Connection Interrupted

    I think it is version 1. I do not have the pogo pins. I did purchase a new print bed cable, as the one I had pretty much disintegrated. There is a...
    Post by: studiver13, Dec 23, 2019 in forum: Troubleshooting
  14. studiver13
    Post

    Connection Interrupted

    I followed your directions and my OCD is now happy that my printer name is correct. However I am unable to connect to my printer via octoprint and...
    Post by: studiver13, Dec 22, 2019 in forum: Troubleshooting
  15. studiver13
    Thread

    Connection Interrupted

    I haven't used my Robo in quite some time because I was having some serious issues with it and I got tired of always fixing it. I am now trying to...
    Thread by: studiver13, Dec 22, 2019, 43 replies, in forum: Troubleshooting