1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. bryson bishop
    Post

    Unresolved Heated bed replacement

    Okay! Thanks for clearing things up
    Post by: bryson bishop, Jul 27, 2016 in forum: Troubleshooting
  2. bryson bishop
    Post

    Unresolved Heated bed replacement

    It doesn't matter which ones go where as far as the heater goes does it because it is a semiconductor?
    Post by: bryson bishop, Jul 27, 2016 in forum: Troubleshooting
  3. bryson bishop
    Post

    Unresolved Odd Noise when powering on

    Mine does the exact same thing. Don't know exactly what the problem is tho.
    Post by: bryson bishop, Jul 27, 2016 in forum: Troubleshooting
  4. bryson bishop
    Post

    Unresolved Heated bed replacement

    [IMG] Here are where the connections of the old heated bed are on my ramps [IMG] And here are what the connections to the new one looks like
    Post by: bryson bishop, Jul 27, 2016 in forum: Troubleshooting
  5. bryson bishop
    Post

    Unresolved Heated bed replacement

    Yeah my wiring is different. My wires are held in with screws to the ramps board. But I will send a picture
    Post by: bryson bishop, Jul 27, 2016 in forum: Troubleshooting
  6. bryson bishop
    Thread

    Unresolved Heated bed replacement

    I recently had to order a new heated bed after cracking mine trying to get a print off. The problem is the bed that I ordered has completely...
    Thread by: bryson bishop, Jul 27, 2016, 13 replies, in forum: Troubleshooting
  7. bryson bishop
    Post

    Partially Solved Layers far apart

    Just ordered 2 of them just to be safe. When they come in ill do a follow up on if it helps or not.
    Post by: bryson bishop, Jul 8, 2016 in forum: Troubleshooting
  8. bryson bishop
    Post

    Partially Solved Layers far apart

    Thanks guys!
    Post by: bryson bishop, Jul 8, 2016 in forum: Troubleshooting
  9. bryson bishop
    Post

    Partially Solved Layers far apart

    Which do you recommend? Or are they both the same
    Post by: bryson bishop, Jul 8, 2016 in forum: Troubleshooting
  10. bryson bishop
    Post

    Partially Solved Layers far apart

    Okay I have just noticed something before I started printing. I heated up the hot end and started manually turning the Hobbed bolt gear with my...
    Post by: bryson bishop, Jul 8, 2016 in forum: Troubleshooting
  11. bryson bishop
    Post

    Partially Solved Layers far apart

    Okay I will try that and print again and come back with results
    Post by: bryson bishop, Jul 8, 2016 in forum: Troubleshooting
  12. bryson bishop
    Post

    Partially Solved Layers far apart

    Here's the Hobbed bolt [IMG]
    Post by: bryson bishop, Jul 8, 2016 in forum: Troubleshooting
  13. bryson bishop
    Post

    Partially Solved Layers far apart

    Yes that's exactly what it does. The gear moves but the filament hesitates to go through for a second.
    Post by: bryson bishop, Jul 8, 2016 in forum: Troubleshooting
  14. bryson bishop
    Post

    Partially Solved Layers far apart

    Yes I have even taken some extra steps to make it as tight as possible
    Post by: bryson bishop, Jul 7, 2016 in forum: Troubleshooting
  15. bryson bishop
    Post

    Partially Solved Layers far apart

    Pla. Using oiler. Just cleaned the hot end about 30 min of run time ago. And it just started happening. I've had the printer for a year. I have...
    Post by: bryson bishop, Jul 7, 2016 in forum: Troubleshooting
  16. bryson bishop
    Thread

    Partially Solved Layers far apart

    I don't know exactly what's going on. If it's a flow problem or something like that but if anyone knows anything that would help please let me...
    Thread by: bryson bishop, Jul 7, 2016, 20 replies, in forum: Troubleshooting
  17. bryson bishop
    Post

    Solved Nozzle too close to bed on first layer

    Okay, yeah it turned out good this time. Thanks for the info guys!
    Post by: bryson bishop, Jun 25, 2016 in forum: Troubleshooting
  18. bryson bishop
    Post

    Solved Nozzle too close to bed on first layer

    Heres the files. i have them both printing on the platform. not really sure on how to see if it is broken or not
    Post by: bryson bishop, Jun 25, 2016 in forum: Troubleshooting
  19. bryson bishop
    Post

    Solved Nozzle too close to bed on first layer

    Extruding on and off and ive left the print going and its continuing to do it throughout the print
    Post by: bryson bishop, Jun 25, 2016 in forum: Troubleshooting
  20. bryson bishop
    Post

    Solved Nozzle too close to bed on first layer

    Having a little problem now. the first layer goes down now but looks like this. any suggestions?...
    Post by: bryson bishop, Jun 25, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 23 Next >
Search Again
Page 1 of 2