1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 5 of 5
  1. TomerO
    Post

    Solved Where is my D10 terminal? And why is my Arduino shield different?

    Interesting because I also have an R1+ and the board is grey and there seem to be some differences... mainly in the fan area (bottom right in your...
    Post by: TomerO, May 22, 2016 in forum: Troubleshooting
  2. TomerO
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    I don't know what 3Q is, but checkout page 18 of this thread Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, May 22, 2016 in forum: Mods and Upgrades
  3. TomerO
    Post

    Unresolved Z-axis not homing after updating firmware

    Sounds like your z end stop is disconnected... under each connection to the z screws there is a small switch. One or both is probably either too...
    Post by: TomerO, May 22, 2016 in forum: Troubleshooting
  4. TomerO
    Post

    Unanswered Practically 100% failure rate with longer (>1 hour) prints for various reasons.

    Sorry didn't see the original stl. If it's supposed to have gaps then idk Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, May 22, 2016 in forum: Troubleshooting
  5. TomerO
    Post

    Unanswered Practically 100% failure rate with longer (>1 hour) prints for various reasons.

    Offsets look correct assuming you didn't change anything. Well that proves it is a slicer problem... Did you change anything or did you use the...
    Post by: TomerO, May 22, 2016 in forum: Troubleshooting
  6. TomerO
    Post

    Unanswered Practically 100% failure rate with longer (>1 hour) prints for various reasons.

    Wrong diameter settings can also cause this. What is configured as your filament diameter and your nozzle diameter? Also I highly suggest you...
    Post by: TomerO, May 22, 2016 in forum: Troubleshooting
  7. TomerO
    Post

    Unanswered Practically 100% failure rate with longer (>1 hour) prints for various reasons.

    Why is it missing so much on the inside. Is that by design? Sent from my Nexus 5 using Tapatalk
    Post by: TomerO, May 22, 2016 in forum: Troubleshooting
  8. TomerO
    Post

    Unanswered Practically 100% failure rate with longer (>1 hour) prints for various reasons.

    Checking the fans is a good start. I would also suspect calibration issues. They might not be noticeable in small prints, but when you print big...
    Post by: TomerO, May 22, 2016 in forum: Troubleshooting
  9. TomerO
    Post

    RGB LED Wiring Diagram and Code

    Yeah, but I don't have real need for it except making it flash at startup here. I will either hack something in the code or I will just do without it
    Post by: TomerO, May 21, 2016 in forum: Mods and Upgrades
  10. TomerO
    Post

    RGB LED Wiring Diagram and Code

    Yup, I looked into it and expect for the power supply pin which works only if you added something extra like a relay there isn't any indication. I...
    Post by: TomerO, May 21, 2016 in forum: Mods and Upgrades
  11. TomerO
    Post

    RGB LED Wiring Diagram and Code

    Found the problem with the LEDs not flashing. The code makes them flash on the board's startup, but since I have a USB cable connect to the board...
    Post by: TomerO, May 21, 2016 in forum: Mods and Upgrades
  12. TomerO
    Post

    RGB LED Wiring Diagram and Code

    I was able to display the full range of colors using these pins (4,5,6, same as you, different board though) so I doubt its the problem, I will...
    Post by: TomerO, May 21, 2016 in forum: Mods and Upgrades
  13. TomerO
    Post

    RGB LED Wiring Diagram and Code

    I love the idea so I decided to try it. I have a Robo3D R1+ with the RC6 marlin firmware. The wiring worked well (I didn't go directly with the...
    Post by: TomerO, May 20, 2016 in forum: Mods and Upgrades
  14. TomerO
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Just wanted to update for feature references that I used to have a leveling problem with one of my corners and now I found time to switch to MESH...
    Post by: TomerO, May 10, 2016 in forum: Mods and Upgrades
  15. TomerO
    Thread

    S3D + Octopi automation

    Hey guys, After a lot of time I only used other people's resources I decided its time to start sharing some =] This is nothing big, just a python...
    Thread by: TomerO, May 7, 2016, 0 replies, in forum: Software
  16. TomerO
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    Just updated and printed a calibration cube and everything seems legit besides maybe some config changes (omg the ABL is so much faster and the...
    Post by: TomerO, May 3, 2016 in forum: Mods and Upgrades
  17. TomerO
    Post

    R1+ Firmware V2 - What's Changed

    I was just looking into the v2 and contacted support when I saw this. They updated the change log in the web page :) I also pointed them here in...
    Post by: TomerO, May 2, 2016 in forum: Software
Find older messages
Showing results 81 to 97 of 97
Search Again
Page 5 of 5