1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. TheOneWhoWhelms
    Post

    Community Favorite Taking the R1+ ramps and rewiring to make generic Ramps Work

    Hey this ended up being my issue. Thanks again for your help through this process, it's working perfectly now!
    Post by: TheOneWhoWhelms, Jun 15, 2020 in forum: Mods and Upgrades
  2. TheOneWhoWhelms
    Post

    Community Favorite Taking the R1+ ramps and rewiring to make generic Ramps Work

    Ahh good call sir, I meant to move the drivers over to the new RAMPS board but totally forgot as the replacement board already had them installed....
    Post by: TheOneWhoWhelms, Jun 15, 2020 in forum: Mods and Upgrades
  3. TheOneWhoWhelms
    Post

    Solved R1+ Heated Bed Issue

    Good call sir, I ended up replacing the RAMPS board per Geof's instructions, and it actually seems to be working now. I should try to search a bit...
    Post by: TheOneWhoWhelms, Jun 15, 2020 in forum: Troubleshooting
  4. TheOneWhoWhelms
    Post

    Community Favorite Taking the R1+ ramps and rewiring to make generic Ramps Work

    Hey guys, thank you everyone who has contributed to this! This helped me a ton, just replaced the board with a generic RAMPS 1.4 board this...
    Post by: TheOneWhoWhelms, Jun 15, 2020 in forum: Mods and Upgrades
  5. TheOneWhoWhelms
    Thread

    Solved R1+ Heated Bed Issue

    [IMG] Hey guys, just curious to know if any of you have dealt with this before. It looks like the connector for the heated bed is somehow...
    Thread by: TheOneWhoWhelms, Jun 15, 2020, 3 replies, in forum: Troubleshooting
  6. TheOneWhoWhelms
    Post

    Solved Replacement Stepper motor wire

    Gahh, I just broke that same cable this evening. Not thrilled, but glad that someone else was able to source the cable. Thanks!
    Post by: TheOneWhoWhelms, Feb 24, 2019 in forum: Troubleshooting
  7. TheOneWhoWhelms
    Post

    Partial Answer Layer lines on my prints are not even

    Thank you for this, however is it likely this would be an STL issue if I've been printing many of the same STLs for quite awhile without issues? I...
    Post by: TheOneWhoWhelms, Feb 1, 2019 in forum: Troubleshooting
  8. TheOneWhoWhelms
    Post

    Partial Answer Layer lines on my prints are not even

    I'm having the same issue as well, printing with PLA. I've done the following: -Tried a belt tensioner, no change -Replaced the nozzle, no change...
    Post by: TheOneWhoWhelms, Jan 31, 2019 in forum: Troubleshooting
  9. TheOneWhoWhelms
    Post

    Solved Strange Extrusion Issue

    @mark tomlinson, thank you so much for your help! The issue with this was the extruder fan. Swapped that out and it resumed working.
    Post by: TheOneWhoWhelms, Sep 2, 2018 in forum: Troubleshooting
  10. TheOneWhoWhelms
    Post

    Solved Strange Extrusion Issue

    Awesome, thank you! I think I may have narrowed down the cause of the issue, it looks like the extruder fan is shot, I removed it and tested it...
    Post by: TheOneWhoWhelms, Sep 2, 2018 in forum: Troubleshooting
  11. TheOneWhoWhelms
    Post

    Solved Strange Extrusion Issue

    Perfect, thanks! I'll try to calibrate the extruder a few times first just to see if that makes a difference, and then I'll look into the other...
    Post by: TheOneWhoWhelms, Aug 27, 2018 in forum: Troubleshooting
  12. TheOneWhoWhelms
    Post

    Solved Strange Extrusion Issue

    Thank you! I've actually had this thing for just over 2 years, and I've never had an issue quite like this. I've been pretty good at cold-pulling...
    Post by: TheOneWhoWhelms, Aug 27, 2018 in forum: Troubleshooting
  13. TheOneWhoWhelms
    Post

    Solved Strange Extrusion Issue

    Thank you! I've actually been using this for over 2 years without any adjustments/calibrations. But I will try to calibrate this in the next day...
    Post by: TheOneWhoWhelms, Aug 26, 2018 in forum: Troubleshooting
  14. TheOneWhoWhelms
    Post

    Solved Strange Extrusion Issue

    I have not look into calibrating the extruder, but I will try it, thanks! I didn't think about it just because I haven't changed anything lately....
    Post by: TheOneWhoWhelms, Aug 26, 2018 in forum: Troubleshooting
  15. TheOneWhoWhelms
    Thread

    Solved Strange Extrusion Issue

    Hello! I'm having a strange extrusion issue on my R1+, it almost seems like the stepper is pushing too much filament through the hotend, but then...
    Thread by: TheOneWhoWhelms, Aug 26, 2018, 10 replies, in forum: Troubleshooting
Showing results 1 to 15 of 15
Search Again