1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. fastbike02
    Thread

    PID AUtotune

    could you help me out and explain the PID auto tune routine?
    Thread by: fastbike02, May 4, 2017, 1 replies, in forum: Mods and Upgrades
  2. fastbike02
    Thread

    Answered Full Graphics Display

    Does anyone know how to remove the sound and extra extruders on the full graphics lcd using the oem robo v3 firmware? I have tried upgrading and...
    Thread by: fastbike02, Apr 26, 2017, 1 replies, in forum: Troubleshooting
  3. fastbike02
    Post

    Solved help with firmware updates

    if it's one of the cheap red board lcds off ebay the contrast is super sensitive
    Post by: fastbike02, Apr 20, 2017 in forum: General Questions
  4. fastbike02
    Post

    Marlin Firmware Upgrade 1.1.0 RC8 & RCBugFix (For R1 & R1+PLUS)

    is it possible to use auto bed leveling instead of mesh with the RCBF_MESH_TR82_04-16 firmware? (I really only want the nicer full graphics lcd...
    Post by: fastbike02, Apr 20, 2017 in forum: Mods and Upgrades
  5. fastbike02
    Post

    Community Favorite Alternative to the Lead Screw Upgrade Kit

    Well darn, how will these affect the quality of the print compared to tr8*2? and is the mesh firmware better than the v3
    Post by: fastbike02, Apr 17, 2017 in forum: Mods and Upgrades
  6. fastbike02
    Post

    Community Favorite Alternative to the Lead Screw Upgrade Kit

    I purchased these rods on ebay and wanted to ask if changing the steps to 1600 would work with the 2mm pitch of these? thanks in advance! Tr8 8mm...
    Post by: fastbike02, Apr 17, 2017 in forum: Mods and Upgrades
  7. fastbike02
    Post

    Solved Auto level troubles

    Well I feel like an idiot.... it was the bed ribbon cable, I ended up taking the little bracket off that holds it to the rear support and now no...
    Post by: fastbike02, Apr 16, 2017 in forum: Troubleshooting
  8. fastbike02
    Post

    Solved Auto level troubles

    no it homes fine, when I run a G29 in my start code of cura it grinds the y axis trying to move to the last 3 points. it's like the printer...
    Post by: fastbike02, Apr 16, 2017 in forum: Troubleshooting
  9. fastbike02
    Post

    Solved Auto level troubles

    So what do I need to do to get the printer to stop trying to go past its forward limit?
    Post by: fastbike02, Apr 16, 2017 in forum: Troubleshooting
  10. fastbike02
    Thread

    Solved Auto level troubles

    When I add the code G29 to cura it pushes the bed so far forward that it grinds the motors for a split second, Also my second set of point it...
    Thread by: fastbike02, Apr 15, 2017, 8 replies, in forum: Troubleshooting
  11. fastbike02
    Post

    Solved How do you properly remove Filament

    probably not right but I heat mine up and back it out till I can push the feed arm and rip it out
    Post by: fastbike02, Apr 12, 2017 in forum: General Questions
  12. fastbike02
    Post

    Epic bad print!

    Knock on wood mine has never messed up that bad while doing an overnight print
    Post by: fastbike02, Apr 12, 2017 in forum: Show and Tell
  13. fastbike02
    Post

    Solved help with firmware updates

    thank yall!! after some (more) research I will be staying with the robo 3d firmware I have now! Hopefully it all flashes well!
    Post by: fastbike02, Apr 11, 2017 in forum: General Questions
  14. fastbike02
    Post

    Solved help with firmware updates

    if so is it worth the upgrade? and if so which one would i need, as I see like 4 different ones in that post ? again sorry for all the questions
    Post by: fastbike02, Apr 11, 2017 in forum: General Questions
  15. fastbike02
    Post

    Solved help with firmware updates

    All the files come from Robo 3d except the Marlin-1.0.2-1, and I only used the dogm_lcd_implementation.h file from it for the updated lcd display....
    Post by: fastbike02, Apr 11, 2017 in forum: General Questions
  16. fastbike02
    Thread

    Solved help with firmware updates

    Please forgive my ignorance but I have spent the last 2 days reading threads and trying to figure out how/if I should update my firmware. I...
    Thread by: fastbike02, Apr 11, 2017, 9 replies, in forum: General Questions
Showing results 1 to 16 of 16
Search Again