1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 10
  1. Toro1966
    Post

    Anyone have experience with Palette+ ?

    So I just bought, returned, and today rebought the Palette +. I returned the first one because it arrived damaged I believe. I say I believe...
    Post by: Toro1966, Nov 14, 2017 in forum: General Questions
  2. Toro1966
    Post

    Issues with overhang/underside of prints.

    I know you've tried this with multiple models, but try something other than the viper. I get great prints and I have never been able to print that...
    Post by: Toro1966, Aug 6, 2017 in forum: Troubleshooting
  3. Toro1966
    Post

    Answered Supports not staying stuck to bed, ruining prints

    4mm Mark - been using the same ones for 6 months with no issue. Haven't had to use a raft before. Not sure why this just started.
    Post by: Toro1966, Feb 1, 2017 in forum: Troubleshooting
  4. Toro1966
    Thread

    Answered Supports not staying stuck to bed, ruining prints

    Hey guys, just recently started having this issue and I print a lot. Using S3D and hair spray, with MeltInk PLA. temps are about 55/192....
    Thread by: Toro1966, Feb 1, 2017, 4 replies, in forum: Troubleshooting
  5. Toro1966
    Post

    E3D v6 Information, Installation Guides, and Review

    Check to make sure the correct port is selected. Also check to make sure you don't have any other programs open using the printer (S3D, MC, etc)
    Post by: Toro1966, Jan 28, 2017 in forum: Mods and Upgrades
  6. Toro1966
    Post

    Solved Extruder Calibration Issue

    What's amazing is if I bump it up to 195 it extrudes perfectly. I've already ran autotune as well....
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  7. Toro1966
    Post

    Solved Extruder Calibration Issue

    Thanks Waldo - we must have posted at the same time. Just saw your response. Appreciate it.
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  8. Toro1966
    Post

    Solved Extruder Calibration Issue

    That's unfortunately what I was thinking. Thanks for the quick help.
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  9. Toro1966
    Post

    Solved Extruder Calibration Issue

    Thanks Mark - any thoughts on corrective measures? Just print at a higher temp? I can do that of course, I just get concerned about stringing....
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  10. Toro1966
    Post

    Solved Extruder Calibration Issue

    I even can see on the LCD what value is in the printer.
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  11. Toro1966
    Post

    Solved Extruder Calibration Issue

    Yup
    Post by: Toro1966, Jan 23, 2017 in forum: Troubleshooting
  12. Toro1966
    Thread

    Solved Extruder Calibration Issue

    Hey guys - went to recalibrate the extruder today and I'm having some issues. No matter what I set the esteps to, I am still underextruding (85...
    Thread by: Toro1966, Jan 23, 2017, 12 replies, in forum: Troubleshooting
  13. Toro1966
    Post

    E3DV6 Hotend Installation Guide on Robo R1+

    Sorry. Meant to fix that link. Here you go. These should work. I'll get an updated version in the next week or so....
    Post by: Toro1966, Jan 15, 2017 in forum: Mods and Upgrades
  14. Toro1966
    Post

    Solved Jerk Settings - Marlin Firmware Upgrade

    Did you do an M502 and M500 after your upload of the new firmware? Also - did you confirm you downloaded the correct file?
    Post by: Toro1966, Jan 7, 2017 in forum: Troubleshooting
  15. Toro1966
    Post

    What to avoid?

    Because you need something to guide the filament down to the heat break - or the hobb bolt will just chew up the filament. It's just not rigid...
    Post by: Toro1966, Jan 2, 2017 in forum: Printing Filament
  16. Toro1966
    Post

    What to avoid?

    Also, you will not be able to reliably print flex filament with stock hotend Sent from my iPhone using Tapatalk
    Post by: Toro1966, Jan 2, 2017 in forum: Printing Filament
  17. Toro1966
    Thread

    Answered Babystepping multiplier

    Hey guys - I am very familiar with using the babystepping function with my LCD. That said, what I am trying to find out is what units are default?...
    Thread by: Toro1966, Dec 30, 2016, 1 replies, in forum: General Questions
  18. Toro1966
    Post

    Solved Printer's won't print from SD

    Was definitely the problem. Since I started ejecting the SD from the PC, all has been well with the force......Thanks guys!
    Post by: Toro1966, Dec 28, 2016 in forum: Troubleshooting
  19. Toro1966
    Post

    Solved Printer's won't print from SD

    Thanks guys - other than the formatter that Waldo recommended - I have literally tried just about everything. Very inconsistent. Even with brand...
    Post by: Toro1966, Dec 28, 2016 in forum: Troubleshooting
  20. Toro1966
    Post

    Solved Printer's won't print from SD

    All three though? And not consistently. I have also changed out the SD cards - which worked for a couple of days and then the same issue.
    Post by: Toro1966, Dec 26, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 187 Next >
Search Again
Page 1 of 10