1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Erin-Ellen Winfree
    Post

    Solved Runaway Heated Bed

    I imagine I did something stupid when I installed the firmware. Just turned it on again and I am not getting immediate heat on the bed. Thanks...
    Post by: Erin-Ellen Winfree, May 6, 2019 in forum: Troubleshooting
  2. Erin-Ellen Winfree
    Post

    Solved Runaway Heated Bed

    Ha ha, PID tuning fixed it. Pay no attention to me, I'm a big dummy.
    Post by: Erin-Ellen Winfree, May 5, 2019 in forum: Troubleshooting
  3. Erin-Ellen Winfree
    Post

    Solved Runaway Heated Bed

    Sorry to double post. I just read back through the thread and sure enough, as soon as I power the printer on the bed starts to heat up. SOOO, I...
    Post by: Erin-Ellen Winfree, May 5, 2019 in forum: Troubleshooting
  4. Erin-Ellen Winfree
    Post

    Solved Runaway Heated Bed

    So I'm finally back at it. I've been through a few surgeries recently and haven't been messing with this printer much in the downtime. I finally...
    Post by: Erin-Ellen Winfree, May 5, 2019 in forum: Troubleshooting
  5. Erin-Ellen Winfree
    Post

    Solved Runaway Heated Bed

    I suspected as much, but I didn't want to guess.
    Post by: Erin-Ellen Winfree, Feb 3, 2019 in forum: Troubleshooting
  6. Erin-Ellen Winfree
    Post

    Solved Runaway Heated Bed

    Sorry for being unresponsive guys. I've been super swamped lately. What is the SSR? I googled it and got Solid State Relay, but I don't know...
    Post by: Erin-Ellen Winfree, Feb 3, 2019 in forum: Troubleshooting
  7. Erin-Ellen Winfree
    Post

    Solved Runaway Heated Bed

    Thanks for the quick reply. It at least appears to keep climbing until it errors out. I haven't read the temperature at the bed yet. It only...
    Post by: Erin-Ellen Winfree, Jan 17, 2019 in forum: Troubleshooting
  8. Erin-Ellen Winfree
    Thread

    Solved Runaway Heated Bed

    Hey again guys, I got frustrated after replacing my RAMPS board/adding a mosfet for the bed heater and gave up for awhile. I wanted to make a...
    Thread by: Erin-Ellen Winfree, Jan 17, 2019, 14 replies, in forum: Troubleshooting
  9. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    At any rate you have been unendingly helpful and I'll likely get a new power supply soon as well. I'll be testing another outlet first though.
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  10. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    hmm, maybe the outlet isn't grounded?
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  11. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    What should the AC be saying? Should it also read 12?
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  12. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    12.11v :) My bad, I have only watched one Youtube video on multimeter usage. In that case, I think I'm golden over this way. About to hook up...
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  13. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    See, that's the weird part. It is functional right now with the old arduino that has a broken voltage regulator. I can turn it on, connect it to...
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  14. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    I tested at the attachment screws and was actually getting 26 at first. I actually dialed the screw back a little.
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  15. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    No idea why I'm getting 24v? In one of my other threads I mentioned that I replaced a capacitor in the power supply and it is physically larger...
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  16. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    [ATTACH] [ATTACH]
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  17. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    Cool, I'm out buying an Arduino. Will post later.
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  18. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    When I fixed the endstops everything works now. I just need one more Arduino so I have a working voltage regulator. I am pretty sure that...
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  19. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    Internet to the rescue. I had my endstops wired wrong. I will certainly be writing a part about that in my how to post.
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
  20. Erin-Ellen Winfree
    Post

    Partial Answer R1+ Bed Not Heating

    Back again with more woes. I wired up my newest ramps and arduino and got smoke again. I switched it off very quickly but who knows if it was...
    Post by: Erin-Ellen Winfree, Nov 15, 2018 in forum: Troubleshooting
Showing results 1 to 20 of 40 Next >
Search Again
Page 1 of 2