1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. romero3d
    Post

    Robo3d R1 with new printed modular X carriage and E3d V6

    Yes Robert, I was so excited to print all the part and I didn't calibrate the extruder, plus I was using a new white Makerbot filament....
    Post by: romero3d, Mar 22, 2016 in forum: Show and Tell
  2. romero3d
    Post

    Robo3d R1 with new printed modular X carriage and E3d V6

    I printed the carriage on PLA Pro from MatterHackers.
    Post by: romero3d, Mar 22, 2016 in forum: Show and Tell
  3. romero3d
    Thread

    Robo3d R1 with new printed modular X carriage and E3d V6

    [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] Hi guys I wanted to share the pics with the new modular X carriage from...
    Thread by: romero3d, Mar 21, 2016, 8 replies, in forum: Show and Tell
  4. romero3d
    Post

    Solved Hotend Screws

    [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] [ATTACH] Hey guys, like I said here are some of the pictures of the installed E3d V6 on the...
    Post by: romero3d, Mar 19, 2016 in forum: Troubleshooting
  5. romero3d
    Post

    MatterControl 1.5 not auto level

    Thanks for checking, I think I have problems with the firmware. I re-installed the 1.4 since I had to print something and then I will play with...
    Post by: romero3d, Mar 4, 2016 in forum: Troubleshooting
  6. romero3d
    Post

    Solved Hotend Screws

    Thanks Mark, looks good to me too, but I wanted somebody else opinion. I will upload some more pic when I finish installation. Thanks again.
    Post by: romero3d, Mar 4, 2016 in forum: Troubleshooting
  7. romero3d
    Post

    Solved Hotend Screws

    Hi Mike, i just did buy a e3d V6 and I printed the x carriage you design. Is these how I supposed to install the e3d? See...
    Post by: romero3d, Mar 3, 2016 in forum: Troubleshooting
  8. romero3d
    Post

    MatterControl 1.5 not auto level

    Yes, it has that. did you try the 1.5?
    Post by: romero3d, Mar 1, 2016 in forum: Troubleshooting
  9. romero3d
    Thread

    MatterControl 1.5 not auto level

    I just install the matter control 1.5 and it didn't auto level. Its that normal or something wrong?
    Thread by: romero3d, Mar 1, 2016, 6 replies, in forum: Troubleshooting
  10. romero3d
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    Thanks Mark, I did the change on startup and its working fine, when I set the temperature for PLA at 210, print the first two layers fine then...
    Post by: romero3d, Feb 20, 2016 in forum: Troubleshooting
  11. romero3d
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    Thanks Mark, I have problems with temperature, I order some thermistors from Amazon and I will try with a newone, the extruder drops down like 10...
    Post by: romero3d, Feb 20, 2016 in forum: Troubleshooting
  12. romero3d
    Post

    Solved Extruder heating up, then cooling back down when it starts to print.

    I have the same problem, plus my power supply make a noise all the time when printing. Where did you buy the power supply? Thanks
    Post by: romero3d, Feb 19, 2016 in forum: Troubleshooting
  13. romero3d
    Post

    Unanswered ROBO R1 +

    Joaquin, Im from Argentina as well, Im new on this technology, I have my RoBo like one year (I love it), I don't going to give recommendation but...
    Post by: romero3d, Jan 28, 2016 in forum: General Questions
Showing results 1 to 13 of 13
Search Again