1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Rascal
    Post

    E3D PT100, how to install and configure

    You will have to contact utilimaker, it may require a jumper or resistor or you have to do something else, I had a few issues with my robo when I...
    Post by: Rascal, Sep 25, 2016 in forum: Mods and Upgrades
  2. Rascal
    Post

    E3D PT100, how to install and configure

    It is in that article I sent you fyi...
    Post by: Rascal, Sep 25, 2016 in forum: Mods and Upgrades
  3. Rascal
    Post

    E3D PT100, how to install and configure

    http://reprap.org/wiki/Ultimaker's_v1.5.7_PCB Fin the pins, email utilimaker for any other info
    Post by: Rascal, Sep 25, 2016 in forum: Mods and Upgrades
  4. Rascal
    Post

    Unresolved S3D; Good For You? Sucks for Me!

    Yes, but i spent 150 on S3d ...
    Post by: Rascal, May 7, 2016 in forum: Troubleshooting
  5. Rascal
    Post

    Unresolved S3D; Good For You? Sucks for Me!

    No it was awesome before S3d! I made that joystick and tons of brackets
    Post by: Rascal, May 7, 2016 in forum: Troubleshooting
  6. Rascal
    Post

    Unresolved S3D; Good For You? Sucks for Me!

    I dont know, Im at my wits end with this thing
    Post by: Rascal, May 7, 2016 in forum: Troubleshooting
  7. Rascal
    Post

    Unresolved S3D; Good For You? Sucks for Me!

    I just need to print these damn parts so I can get my Titan and V6 operational, if not ima see how much a print for hire cost.
    Post by: Rascal, May 7, 2016 in forum: Troubleshooting
  8. Rascal
    Post

    Unresolved S3D; Good For You? Sucks for Me!

    It is printing via SD card, im going to see if perhaps some kind of com4 error was messing it up first.
    Post by: Rascal, May 7, 2016 in forum: Troubleshooting
  9. Rascal
    Post

    Unresolved S3D; Good For You? Sucks for Me!

    Yeah but it was very fast and like 130 percent extrusion! the part that is taking 4 hours now was done in an hour and 30 with 240, its CF PLA too btw.
    Post by: Rascal, May 7, 2016 in forum: Troubleshooting
  10. Rascal
    Post

    Unresolved S3D; Good For You? Sucks for Me!

    [ATTACH] This Spacer was done @ 240 with PLA! It is almost perfect!.[ATTACH] [ATTACH] These 2 fail prints are quite good except the one on the...
    Post by: Rascal, May 7, 2016 in forum: Troubleshooting
  11. Rascal
    Post

    Unresolved S3D; Good For You? Sucks for Me!

    Is this the same file you had posted previously? I tried that one already and wasnt impressed. The Middle section at the circle is similar to the...
    Post by: Rascal, May 7, 2016 in forum: Troubleshooting
  12. Rascal
    Thread

    Unresolved S3D; Good For You? Sucks for Me!

    Either my Robo has gone bad ... bought it in Feb... Or S3D is needing a reinstall or something.. Anyway check these pictures out before I lay some...
    Thread by: Rascal, May 7, 2016, 17 replies, in forum: Troubleshooting
  13. Rascal
    Post

    Simplify 3d

    It was no good so I just did some tweaking after reading a few things and still have a few fail layers but overall good structure, which makes me...
    Post by: Rascal, May 6, 2016 in forum: Software
  14. Rascal
    Post

    Simplify 3d

    Thanks, I will have to try it. I was putting off the whole 3d printer thing till the weekend this week to avoid any headaches :)
    Post by: Rascal, May 6, 2016 in forum: Software
  15. Rascal
    Post

    Simplify 3d

    If you get a really good print can you fill me in on your settings! I trashed two prints, kinda irritated, but I have strings and its terrible!
    Post by: Rascal, May 1, 2016 in forum: Software
  16. Rascal
    Post

    PolyCarb and Bridge Nylon.

    OMG, Disaster on the setting in S3D! they produced 2 garbage prints thus far, my spacer block for the V6 came out fine somehow. Ill have to tinker...
    Post by: Rascal, May 1, 2016 in forum: Printing Filament
  17. Rascal
    Post

    PolyCarb and Bridge Nylon.

    Simplyfi 3d!
    Post by: Rascal, Apr 29, 2016 in forum: Printing Filament
  18. Rascal
    Post

    PolyCarb and Bridge Nylon.

    I upgraded to the pro program .. im printing 2 parts at once .. ill never go back :)
    Post by: Rascal, Apr 29, 2016 in forum: Printing Filament
  19. Rascal
    Post

    PolyCarb and Bridge Nylon.

    Thank You very much for your dedicated assistance Mark, I appreciate the quick feedback and ideas
    Post by: Rascal, Apr 29, 2016 in forum: Printing Filament
  20. Rascal
    Post

    PolyCarb and Bridge Nylon.

    [ATTACH] I managed to print this whole thing without slicer errors and now I am trying to reprint the cover as I ran out of filament with the...
    Post by: Rascal, Apr 29, 2016 in forum: Printing Filament
Showing results 1 to 20 of 31 Next >
Search Again
Page 1 of 2