1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Jamie_1
    Post

    NinjaFlex filament

    Yes, email the people at Robo 3D and they send you an stl file. It replaces the extruded housing and perfectly fits a Bowden tube inside, so it...
    Post by: Jamie_1, Feb 23, 2017 in forum: Printing Filament
  2. Jamie_1
    Post

    Answered Enclosure for abs?

    Ok thanks Sent from my iPhone using Tapatalk
    Post by: Jamie_1, Feb 1, 2017 in forum: General Questions
  3. Jamie_1
    Thread

    Answered Enclosure for abs?

    Does anybody know if robo is thinking about selling an enclosure for printing stuff like abs? I really want one but don't want to spend $90 on one...
    Thread by: Jamie_1, Jan 27, 2017, 13 replies, in forum: General Questions
  4. Jamie_1
    Thread

    Solved Enclosure for abs?

    I was just wandering if robo is thinking about selling an enclosure any time soon, besides the one by mile for $90 Sent from my iPhone using...
    Thread by: Jamie_1, Jan 27, 2017, 1 replies, in forum: Troubleshooting
  5. Jamie_1
    Post

    Solved Layers shifting/sliding

    Ok thanks, I will make sure to be careful and check each time that I don't cross the end under another strand. Sent from my iPhone using Tapatalk
    Post by: Jamie_1, Jan 26, 2017 in forum: Troubleshooting
  6. Jamie_1
    Post

    Solved Layers shifting/sliding

    Is this common for spools to come tangled? I bought them directly from the robo 3d website Sent from my iPhone using Tapatalk
    Post by: Jamie_1, Jan 26, 2017 in forum: Troubleshooting
  7. Jamie_1
    Post

    Solved Layers shifting/sliding

    I figured out the problem, it's half of the robo spools I bought have come tangled up. So there is so much tension it can't pull the filament out....
    Post by: Jamie_1, Jan 26, 2017 in forum: Troubleshooting
  8. Jamie_1
    Post

    Solved Layers shifting/sliding

    I figured out the problem, it's half of the robo spools I bought have come tangled up. So there is so much tension it can't pull the filament out....
    Post by: Jamie_1, Jan 26, 2017 in forum: Troubleshooting
  9. Jamie_1
    Post

    Solved Layers shifting/sliding

    Thanks! Sent from my iPhone using Tapatalk
    Post by: Jamie_1, Jan 26, 2017 in forum: Troubleshooting
  10. Jamie_1
    Post

    Solved Layers shifting/sliding

    Thanks! Sent from my iPhone using Tapatalk
    Post by: Jamie_1, Jan 26, 2017 in forum: Troubleshooting
  11. Jamie_1
    Post

    Solved Layers shifting/sliding

    Thanks! Sent from my iPhone using Tapatalk
    Post by: Jamie_1, Jan 26, 2017 in forum: Troubleshooting
  12. Jamie_1
    Post

    Solved Layers shifting/sliding

    Is a lose mechanical bit also the reason that a print like the pig is so bad but then this stand comes out so perfect?[IMG] Sent from my iPhone...
    Post by: Jamie_1, Jan 26, 2017 in forum: Troubleshooting
  13. Jamie_1
    Post

    Solved Layers shifting/sliding

    Ok thank you, I will try that tomorrow and get back to you if it works Sent from my iPhone using Tapatalk
    Post by: Jamie_1, Jan 25, 2017 in forum: Troubleshooting
  14. Jamie_1
    Post

    Solved Layers shifting/sliding

    Yes Sent from my iPhone using Tapatalk
    Post by: Jamie_1, Jan 25, 2017 in forum: Troubleshooting
  15. Jamie_1
    Post

    Solved Layers shifting/sliding

    Ok I'm reading them now, but it's weird that when I made a phone holder about that size it came out perfectly fine and one print I sell and print...
    Post by: Jamie_1, Jan 25, 2017 in forum: Troubleshooting
  16. Jamie_1
    Post

    Solved Layers shifting/sliding

    Ninjaflex was a problem so I don't print with that anymore I only did once. The pig was printed in pla and that is when the layers are sliding...
    Post by: Jamie_1, Jan 25, 2017 in forum: Troubleshooting
  17. Jamie_1
    Post

    Solved Layers shifting/sliding

    I also disassembled some of the parts on the extruder to remove a jam, except I took pictures of how it was and I put it back exactly how it was...
    Post by: Jamie_1, Jan 25, 2017 in forum: Troubleshooting
  18. Jamie_1
    Post

    Solved Layers shifting/sliding

    I did not change any settings in print in pla and medium quality. I'm using matter control and haven't changed anything except once to slow down...
    Post by: Jamie_1, Jan 25, 2017 in forum: Troubleshooting
  19. Jamie_1
    Thread

    Solved Layers shifting/sliding

    Please help I'm new to 3d printing and my layers seem to be shifting/sliding and there is space in between each layer. [IMG] Sent from...
    Thread by: Jamie_1, Jan 25, 2017, 25 replies, in forum: Troubleshooting
  20. Jamie_1
    Post

    Solved prints have splotches/bumps on them

    ok thanks, your blobs and zits link solved my problem. Now I am having perfect prints
    Post by: Jamie_1, Dec 31, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 24 Next >
Search Again
Page 1 of 2