1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Ryan Whitney
    Post

    Community Favorite E3D v6 Information and Installation Guide

    I feel like a complete idiot, but how do I access the config.h file? I'm connected to my R1 plus, have the Arduino software loaded, but not sure...
    Post by: Ryan Whitney, Nov 16, 2017 in forum: Mods and Upgrades
  2. Ryan Whitney
    Thread

    ASA Help

    Just bought my first spool of ASA, anyone try it yet and have some advice/setting to share?
    Thread by: Ryan Whitney, Oct 1, 2017, 1 replies, in forum: Printing Filament
  3. Ryan Whitney
    Post

    Unanswered I'M BACK(With a broken heated bed) Upgrade recomendations?

    I had a lot of issues with ABS, but starting wrapping my Robo with Aluminum foil to cover as many of the air gaps as I could and keep the heat in,...
    Post by: Ryan Whitney, Jan 4, 2017 in forum: Troubleshooting
  4. Ryan Whitney
    Post

    Unanswered I'M BACK(With a broken heated bed) Upgrade recomendations?

    Nice thread guys, I broke my glass bed last week after apparently getting the ratio wrong for PVA glue wash and trying to get a big PETG print...
    Post by: Ryan Whitney, Jan 4, 2017 in forum: Troubleshooting
  5. Ryan Whitney
    Post

    Solved Help - Can't figure out PETG

    Alright guys thanks for all of the help. Took a hiatus for Christmas, but after a few more trials last night everything is dialed in perfectly and...
    Post by: Ryan Whitney, Dec 27, 2016 in forum: Troubleshooting
  6. Ryan Whitney
    Post

    Solved Help - Can't figure out PETG

    Thanks Bill, updating my settings to match!
    Post by: Ryan Whitney, Dec 21, 2016 in forum: Troubleshooting
  7. Ryan Whitney
    Post

    Solved Help - Can't figure out PETG

    Yep, using Matter Control. Z lift = .5mm Retraction length on move = 1mm Wipe after retract not set 1st layer height =.3mm Nominal layer height =...
    Post by: Ryan Whitney, Dec 21, 2016 in forum: Troubleshooting
  8. Ryan Whitney
    Post

    Solved Help - Can't figure out PETG

    This is the beginning of layer 2 right after it dragged the dirty tip perpendicular across the initial layers
    Post by: Ryan Whitney, Dec 21, 2016 in forum: Troubleshooting
  9. Ryan Whitney
    Post

    Solved Help - Can't figure out PETG

    This is the melted Petg on the tip after it drags
    Post by: Ryan Whitney, Dec 21, 2016 in forum: Troubleshooting
  10. Ryan Whitney
    Post

    Solved Help - Can't figure out PETG

    Damn you Toro! Tried it again and watch for the 1st 15 min. First layer looks great with good adhesion, but when the extruder moves to start layer...
    Post by: Ryan Whitney, Dec 21, 2016 in forum: Troubleshooting
  11. Ryan Whitney
    Post

    Solved Help - Can't figure out PETG

    Thanks Waldo. Was going to upload a pic last night but black filament on the black bed was hard to make out. Currently trying the black Hatchbox...
    Post by: Ryan Whitney, Dec 21, 2016 in forum: Troubleshooting
  12. Ryan Whitney
    Thread

    Solved Help - Can't figure out PETG

    I've tried both the black and translucent filament from Hatchbox, varied bed temps from 75 to 90deg C in 5 deg increments, varied the extrusion...
    Thread by: Ryan Whitney, Dec 20, 2016, 16 replies, in forum: Troubleshooting
  13. Ryan Whitney
    Post

    Solved Can't Remove Filament After Printing

    Push/pull method worked without any problems at all. Not sure why I was having so much trouble just pulling after a print, but looks like problem...
    Post by: Ryan Whitney, Aug 25, 2016 in forum: Troubleshooting
  14. Ryan Whitney
    Post

    Solved Can't Remove Filament After Printing

    Ok thanks everyone. I'm definitely at temp (210) and even removing the screws completely doesn't let me pull the filament out by hand and I'm...
    Post by: Ryan Whitney, Aug 22, 2016 in forum: Troubleshooting
  15. Ryan Whitney
    Post

    Solved Can't Remove Filament After Printing

    Tried that also after reading your similar post on a different thread.....didn't help with the screws removed, must be something holding it up in...
    Post by: Ryan Whitney, Aug 22, 2016 in forum: Troubleshooting
  16. Ryan Whitney
    Thread

    Solved Can't Remove Filament After Printing

    Just got my printer a couple weeks ago, but I can't remove the filament after printing. I manually spin the gear in reverse with the feed still at...
    Thread by: Ryan Whitney, Aug 22, 2016, 14 replies, in forum: Troubleshooting
  17. Ryan Whitney
    Post

    filament removal

    Just got my printer a couple weeks ago, but I can't remove the filament after printing. I can manually spin the gear in reverse with the feed...
    Post by: Ryan Whitney, Aug 22, 2016 in forum: General Questions
Showing results 1 to 17 of 17
Search Again