1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Bryson
    Post

    Answered Contacting Robo?

    Just FYI I talked with Jonah at partsbuilt.com and while they don’t have the board he is working on finding a supplier. I also asked about long...
    Post by: Bryson, Jun 12, 2019 in forum: Troubleshooting
  2. Bryson
    Post

    Answered Contacting Robo?

    Yeah we will any recommendations on a board? Bought a 7 dollar one amazon, seemed cheap. Willing to spend more. Has anyone else done this that can...
    Post by: Bryson, Jun 12, 2019 in forum: Troubleshooting
  3. Bryson
    Post

    Answered Contacting Robo?

    Yeah we tried this and it started smoking the minute we powered it up. Those instructions aren’t very good and the pictures are terrible.
    Post by: Bryson, Jun 12, 2019 in forum: Troubleshooting
  4. Bryson
    Thread

    Answered Contacting Robo?

    Has anyone been able to contact robo? I've sent several emails and made phone calls, but no response. Are they even a company anymore? I'm needing...
    Thread by: Bryson, Jun 12, 2019, 7 replies, in forum: Troubleshooting
  5. Bryson
    Post

    Solved Printer Sounds Terrible - Possible Stepper Motor

    So I think we have solved this. The stepper motor sounded terrible and would stop extruding filament, but would do this very randomly. It turns...
    Post by: Bryson, Sep 12, 2017 in forum: Troubleshooting
  6. Bryson
    Post

    Solved Printer Sounds Terrible - Possible Stepper Motor

    I have oiled/seasoned it to the best of my knowledge.
    Post by: Bryson, Sep 11, 2017 in forum: Troubleshooting
  7. Bryson
    Post

    Solved Printer Sounds Terrible - Possible Stepper Motor

    I will check the tension, but I printing PLA at 200C with anywhere from 40-60 mm/s, it usually "skips" at both speeds. What would you recommend...
    Post by: Bryson, Sep 11, 2017 in forum: Troubleshooting
  8. Bryson
    Post

    Solved Printer Sounds Terrible - Possible Stepper Motor

    Yes it turns just fine.
    Post by: Bryson, Sep 11, 2017 in forum: Troubleshooting
  9. Bryson
    Post

    Solved Printer Sounds Terrible - Possible Stepper Motor

    I have posted the video on the thread. Thanks for your help.
    Post by: Bryson, Sep 11, 2017 in forum: Troubleshooting
  10. Bryson
    Post

    Solved Printer Sounds Terrible - Possible Stepper Motor

    Okay here is the link to the video. [MEDIA] Of note is that it only does this every so often and then prints fine for a while, and it is not...
    Post by: Bryson, Sep 11, 2017 in forum: Troubleshooting
  11. Bryson
    Thread

    Solved Printer Sounds Terrible - Possible Stepper Motor

    I have just had this issue start up and thought it might be due to a clog, but after replacing the extruder it appears to be the stepper. Its...
    Thread by: Bryson, Sep 11, 2017, 12 replies, in forum: Troubleshooting
  12. Bryson
    Post

    Partially Solved Jittery Stepper at higher heights

    Thanks all, i will give these a try.
    Post by: Bryson, Aug 30, 2017 in forum: Troubleshooting
  13. Bryson
    Post

    Partially Solved Jittery Stepper at higher heights

    I will try these, what would be the steps to season the extruder? just running prints?
    Post by: Bryson, Aug 30, 2017 in forum: Troubleshooting
  14. Bryson
    Thread

    Partially Solved Jittery Stepper at higher heights

    My printer stepper will start to jitter when the skirt is being laid down, but will be fine after that until it reaches higher heights, somewhere...
    Thread by: Bryson, Aug 30, 2017, 5 replies, in forum: Troubleshooting
  15. Bryson
    Post

    Solved The extruder stepper motor jitters

    This says it is solved. Can you please help by providing what particular response helped solved your issue? My issues is the stepper jitters...
    Post by: Bryson, Aug 30, 2017 in forum: Troubleshooting
Showing results 1 to 15 of 15
Search Again