1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. Momenslythe
    Post

    Squeaking Issues and Bed Adhesion

    I ended up trying Wolfbite by Airwolf3D I had left over from my broken Airwolf printer and that worked better than the glue but I still have a bit...
    Post by: Momenslythe, Sep 8, 2017 in forum: Troubleshooting
  2. Momenslythe
    Post

    Partial Answer Why does my ditto have stretch marks?

    I changed the steps/mm in the EEPROM. Results are below. It is slightly better but still not perfect. [ATTACH]
    Post by: Momenslythe, Sep 7, 2017 in forum: Troubleshooting
  3. Momenslythe
    Post

    Squeaking Issues and Bed Adhesion

    I'm still not sure where I'm supposed to put the 3-in-1 oil. It still squeaks a little bit maybe I just missed a spot with the lithium grease. I...
    Post by: Momenslythe, Sep 7, 2017 in forum: Troubleshooting
  4. Momenslythe
    Post

    Squeaking Issues and Bed Adhesion

    How do you make the slurry? I tried a slurry before but it was too white and it threw off the bed level process. Yeah. I don't have my door...
    Post by: Momenslythe, Sep 6, 2017 in forum: Troubleshooting
  5. Momenslythe
    Post

    Squeaking Issues and Bed Adhesion

    I followed the White Lithium Grease lubrication instructions from the Maintenance doc...
    Post by: Momenslythe, Sep 6, 2017 in forum: Troubleshooting
  6. Momenslythe
    Post

    Partial Answer Why does my ditto have stretch marks?

    I am changing Flow Rate. Feed Rate is still at the default value. I talked to support and they told me to do it in the EEPROM like below. So I'll...
    Post by: Momenslythe, Sep 5, 2017 in forum: Troubleshooting
  7. Momenslythe
    Post

    Partial Answer Why does my ditto have stretch marks?

    I tried doing it at 110% but it looks exactly the same as this ~105% and 100% one. This makes me think the printer is completely ignoring the flow...
    Post by: Momenslythe, Sep 5, 2017 in forum: Troubleshooting
  8. Momenslythe
    Thread

    Squeaking Issues and Bed Adhesion

    My printer makes a horrible squeaking noise when I print. This will either happen later in prints that are small such as 3DBenchy or when the head...
    Thread by: Momenslythe, Sep 1, 2017, 11 replies, in forum: Troubleshooting
  9. Momenslythe
    Post

    Bubbly boat issue

    That may have been the case. The one I printed on the High Quality setting had better bed adhesion and wasn't as bubbly. It is however very rough...
    Post by: Momenslythe, Sep 1, 2017 in forum: Troubleshooting
  10. Momenslythe
    Post

    Partial Answer Why does my ditto have stretch marks?

    I followed the instructions in the video and found my printer was only extruding 95mm when I asked it to extrude 100mm. I adjusted it to 105.26%...
    Post by: Momenslythe, Sep 1, 2017 in forum: Troubleshooting
  11. Momenslythe
    Thread

    Bubbly boat issue

    I'm having trouble with this bubbliness on my ABS print. I used the Low Quality setting for this one and am printing one with the High Quality...
    Thread by: Momenslythe, Aug 31, 2017, 22 replies, in forum: Troubleshooting
  12. Momenslythe
    Post

    Partial Answer Why does my ditto have stretch marks?

    I have not done this nor do I know how to.
    Post by: Momenslythe, Aug 31, 2017 in forum: Troubleshooting
  13. Momenslythe
    Post

    Partial Answer Why does my ditto have stretch marks?

    I printed the ditto with the random z seam alignment. The really noticeable seam is now gone but there are now smaller notches all over the print....
    Post by: Momenslythe, Aug 31, 2017 in forum: Troubleshooting
  14. Momenslythe
    Post

    Partial Answer Why does my ditto have stretch marks?

    Just found it under Preferences > Configure Cura... > Settings > then check "Z Seam Alignment" to have it show up in custom settings. Will try...
    Post by: Momenslythe, Aug 30, 2017 in forum: Troubleshooting
  15. Momenslythe
    Post

    Partial Answer Why does my ditto have stretch marks?

    How do I find that in Cura for Robo? Sorry, forgot to add that in the post but have it there now.
    Post by: Momenslythe, Aug 30, 2017 in forum: Troubleshooting
  16. Momenslythe
    Post

    Partial Answer Why does my ditto have stretch marks?

    Thanks
    Post by: Momenslythe, Aug 30, 2017 in forum: Troubleshooting
  17. Momenslythe
    Thread

    Partial Answer Why does my ditto have stretch marks?

    I'm getting this mark on every ditto I print regardless of print quality setting. I'm not sure why. the mark is more intense when printing at High...
    Thread by: Momenslythe, Aug 30, 2017, 21 replies, in forum: Troubleshooting
Find older messages
Showing results 21 to 37 of 37
Search Again
Page 2 of 2