1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Momenslythe
    Post

    Benchy overhang issue

    I don't know why I didn't see this. Usually I get an email when I get a reply. Yes it was 195C on PLA. I was using this one for the fans:...
    Post by: Momenslythe, Oct 4, 2018 in forum: Troubleshooting
  2. Momenslythe
    Thread

    Benchy overhang issue

    I am having an issue with the overhang in the front of my benchy on my R2. I'm not sure what causes this issue. Both of these are using the same...
    Thread by: Momenslythe, Sep 17, 2018, 3 replies, in forum: Troubleshooting
  3. Momenslythe
    Thread

    Temp Tower Results

    I want to do a couple things with this post. First, I would like to share my results on a temperature tower for my R2 in a variety of...
    Thread by: Momenslythe, Sep 13, 2018, 0 replies, in forum: Troubleshooting
  4. Momenslythe
    Post

    Solved Printer stays put at end of print making bad top layer

    Sorry I left this for a while. I was talking with Robo3D support and had some renovations in the room with my 3D printers. I was able to use...
    Post by: Momenslythe, Nov 1, 2017 in forum: Troubleshooting
  5. Momenslythe
    Post

    Solved Printer stays put at end of print making bad top layer

    I was able to get my C2 to work again with the link. I was able to initiate the C2 spiral test with OctoPrint and am seeing the hotend park for...
    Post by: Momenslythe, Sep 21, 2017 in forum: Troubleshooting
  6. Momenslythe
    Post

    Bubbly boat issue

    I'm not comparing to a Lego brick. I'm comparing to what I get from my C2 printing. My more expensive machine should not have a worse finish. I...
    Post by: Momenslythe, Sep 19, 2017 in forum: Troubleshooting
  7. Momenslythe
    Post

    Bubbly boat issue

    OK I will try the perimeter addition. Is that adding wall thickness or is that something else?
    Post by: Momenslythe, Sep 19, 2017 in forum: Troubleshooting
  8. Momenslythe
    Post

    Bubbly boat issue

    I'm using ABS and bed heat of 80C
    Post by: Momenslythe, Sep 19, 2017 in forum: Troubleshooting
  9. Momenslythe
    Post

    Solved Printer stays put at end of print making bad top layer

    For the heating issue, the last few layers look like they were put down wrong or remelted when the extruder goes over it again. These layers look...
    Post by: Momenslythe, Sep 19, 2017 in forum: Troubleshooting
  10. Momenslythe
    Post

    Bubbly boat issue

    Sorry this took me so long to reply. I don't have a problem with the Low Quality Deprime print but whenever I print something bigger than the...
    Post by: Momenslythe, Sep 19, 2017 in forum: Troubleshooting
  11. Momenslythe
    Post

    Solved Printer stays put at end of print making bad top layer

    My OctoPrint end GCODE looks like yours. When I initiated the kodama print through OctoPrint, I do not see a heavy indent like I did before. I...
    Post by: Momenslythe, Sep 19, 2017 in forum: Troubleshooting
  12. Momenslythe
    Post

    Solved Printer stays put at end of print making bad top layer

    I forgot to check mine last night when I was home. Does the OctoPrint stuff happen even if I initiate the print through the LCD screen?
    Post by: Momenslythe, Sep 14, 2017 in forum: Troubleshooting
  13. Momenslythe
    Post

    Solved Printer stays put at end of print making bad top layer

    Mine does not. I actually forgot to point out that you can see a mark on the tape from when I was doing the C2 spiral test. There's a tiny blue...
    Post by: Momenslythe, Sep 13, 2017 in forum: Troubleshooting
  14. Momenslythe
    Post

    Solved Printer stays put at end of print making bad top layer

    So I tried doing the same print with the end GCODE but have a similar results. Sorry the picture is kind of bad. [ATTACH] After seeing this I...
    Post by: Momenslythe, Sep 13, 2017 in forum: Troubleshooting
  15. Momenslythe
    Post

    Bubbly boat issue

    Oh sorry these pictures are all low quality prints. I had a hard time taking good ones of the high quality so I'm trying to figure that out before...
    Post by: Momenslythe, Sep 12, 2017 in forum: Troubleshooting
  16. Momenslythe
    Post

    Solved Printer stays put at end of print making bad top layer

    Thank you. I think that is what I'm looking for. I'm not sure exactly where I should put that GCODE. I have attached the end of mine below. Would...
    Post by: Momenslythe, Sep 12, 2017 in forum: Troubleshooting
  17. Momenslythe
    Thread

    Solved Printer stays put at end of print making bad top layer

    My C2 (and my R2) sit in place at the end of a print and ends up making a dimple/nipple in that spot on my prints. How can I get the extruder to...
    Thread by: Momenslythe, Sep 12, 2017, 24 replies, in forum: Troubleshooting
  18. Momenslythe
    Post

    Bubbly boat issue

    I don't see the same results in benchy and deprime. My deprime tests look much better at the HQ than my bency does. I was only able to get decent...
    Post by: Momenslythe, Sep 11, 2017 in forum: Troubleshooting
  19. Momenslythe
    Post

    Squeaking Issues and Bed Adhesion

    I'm using the stock slicer settings from Cura for Robo. I'm not sure if that setting is on or off.
    Post by: Momenslythe, Sep 9, 2017 in forum: Troubleshooting
  20. Momenslythe
    Post

    Bubbly boat issue

    Thanks, I will try the Deprime. I've been trying to sort out my bed adhesion issues before figuring out these other print quality ones. I used...
    Post by: Momenslythe, Sep 8, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 37 Next >
Search Again
Page 1 of 2