1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. ballhogjoni
    Thread

    R2 Web Cam?

    Hey does anyone know how to setup the webcam? I can't seem to find it in the control screen options.
    Thread by: ballhogjoni, Jun 3, 2017, 2 replies, in forum: General Questions
  2. ballhogjoni
    Thread

    Reset printer to factory default?

    Is there a way to reset printer to factory default?
    Thread by: ballhogjoni, Jun 3, 2017, 2 replies, in forum: Troubleshooting
  3. ballhogjoni
    Post

    Extruder to far from print bed

    I turned it on this morning and now the screen is unresponsive.
    Post by: ballhogjoni, Jun 3, 2017 in forum: Troubleshooting
  4. ballhogjoni
    Post

    Extruder to far from print bed

    No it didn't show that in the quick start guide.
    Post by: ballhogjoni, Jun 3, 2017 in forum: Troubleshooting
  5. ballhogjoni
    Thread

    Extruder to far from print bed

    I've gone through the z calibration twice and it was -8.2 and -9.0. When I go to do one of the default test prints the extruder is about 2-3mm...
    Thread by: ballhogjoni, Jun 3, 2017, 6 replies, in forum: Troubleshooting
  6. ballhogjoni
    Post

    Unresolved New XXL LCD Causing Bed to Shutdown

    Ya i don't have a fan on mine. I bought the first version years ago. Just started getting back into 3d printing.
    Post by: ballhogjoni, Aug 21, 2016 in forum: Troubleshooting
  7. ballhogjoni
    Post

    Unresolved New XXL LCD Causing Bed to Shutdown

    So after doing some research I think it has nothing to do with the XXL. I watched this video [MEDIA] and it seemed to fix this guys problem....
    Post by: ballhogjoni, Aug 21, 2016 in forum: Troubleshooting
  8. ballhogjoni
    Post

    Unresolved New XXL LCD Causing Bed to Shutdown

    Ya i checked that too. Everything looks ok and will even start the preheat but shuts down the bed after that 70 degrees.
    Post by: ballhogjoni, Aug 21, 2016 in forum: Troubleshooting
  9. ballhogjoni
    Post

    Unresolved New XXL LCD Causing Bed to Shutdown

    It happens with both cases. I'm using PLA.
    Post by: ballhogjoni, Aug 21, 2016 in forum: Troubleshooting
  10. ballhogjoni
    Thread

    Unresolved New XXL LCD Causing Bed to Shutdown

    So I got the XXL LCD from print solid and its causing the bed to shutdown when it hits 70 degrees. I've tested this by having it connected without...
    Thread by: ballhogjoni, Aug 21, 2016, 14 replies, in forum: Troubleshooting
  11. ballhogjoni
    Post

    Unanswered For some reason the printer stops mid print

    What LCD do you recommend?
    Post by: ballhogjoni, Aug 16, 2016 in forum: Troubleshooting
  12. ballhogjoni
    Post

    Unanswered For some reason the printer stops mid print

    middle of a 5 hour build and came back to computer restarting. i guess another reason for the sd card or lcd.
    Post by: ballhogjoni, Aug 16, 2016 in forum: Troubleshooting
  13. ballhogjoni
    Post

    Unanswered For some reason the printer stops mid print

    Ok thanks! That's what i thought. I can't print w/ an SD card that i know of. I have the first gen Robo printer. Also I'm using USB 3 so that...
    Post by: ballhogjoni, Aug 16, 2016 in forum: Troubleshooting
  14. ballhogjoni
    Thread

    Unanswered For some reason the printer stops mid print

    The printer stops mid print for a few seconds and then continues. This causes the extruder to leave excess filament where it stop and also melts...
    Thread by: ballhogjoni, Aug 16, 2016, 24 replies, in forum: Troubleshooting
Find older messages
Showing results 21 to 34 of 34
Search Again
Page 2 of 2