1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 4 of 4
  1. eric tobin
    Post

    Answered setting the fan

    ok, thanks for the help
    Post by: eric tobin, Aug 22, 2017 in forum: General Questions
  2. eric tobin
    Thread

    Answered setting the fan

    is there some code or way to set the fan so it always turns on when your print starts, or am I missing something in the settings menu on how to...
    Thread by: eric tobin, Aug 21, 2017, 4 replies, in forum: General Questions
  3. eric tobin
    Post

    Solved kinks

    got thank you mark, fan was off. gotta remember to check every time, someday I will learn this thing
    Post by: eric tobin, Aug 21, 2017 in forum: Troubleshooting
  4. eric tobin
    Post

    Solved kinks

    it seems to the worst with the abs white clear, had some trouble with some pla, but the clear seems to be the worst
    Post by: eric tobin, Aug 20, 2017 in forum: Troubleshooting
  5. eric tobin
    Post

    Solved kinks

    that's is what it looks like at the top of the hot end.
    Post by: eric tobin, Aug 20, 2017 in forum: Troubleshooting
  6. eric tobin
    Post

    Solved kinks

    [ATTACH] [ATTACH]
    Post by: eric tobin, Aug 20, 2017 in forum: Troubleshooting
  7. eric tobin
    Thread

    Solved kinks

    ok, I got my new hot end first several prints were good, now I seem to be getting a kink in the filament at the top. At least that is what it...
    Thread by: eric tobin, Aug 19, 2017, 7 replies, in forum: Troubleshooting
  8. eric tobin
    Post

    robo service

    update: I finally got a reply from Danny in the service dept. he agreed with me that their two day shipping is messed up and that he would try to...
    Post by: eric tobin, Aug 18, 2017 in forum: General Questions
  9. eric tobin
    Thread

    robo service

    has anyone ever had trouble getting a hold the sales department? I purchased a hotend mon. paid 2 day air, and it still is not here! every time I...
    Thread by: eric tobin, Aug 17, 2017, 4 replies, in forum: General Questions
  10. eric tobin
    Thread

    Solved using flexible filament

    any tips or ideas on using flexible filament? where to look?
    Thread by: eric tobin, Jul 29, 2017, 1 replies, in forum: Troubleshooting
  11. eric tobin
    Thread

    what makes the bed chip?

    printed a part last night, woke up this morning took off the part, it was real sticky in one spot, got it up and had glass on the bottom. usually...
    Thread by: eric tobin, Jul 27, 2017, 2 replies, in forum: General Questions
  12. eric tobin
    Post

    Solved cannot remove extruder

    uhh, I ment link my bad, but I did the trick thank you very much
    Post by: eric tobin, Jul 21, 2017 in forum: Troubleshooting
  13. eric tobin
    Post

    Solved cannot remove extruder

    it was a r1 +plus sorry
    Post by: eric tobin, Jul 21, 2017 in forum: Troubleshooting
  14. eric tobin
    Post

    Solved cannot remove extruder

    thanks for the lick, it was the right screw, just got this, of course a jam, did not want to go messing it up thank you
    Post by: eric tobin, Jul 21, 2017 in forum: Troubleshooting
  15. eric tobin
    Post

    Solved cannot remove extruder

    well I see one screw from the bottom, towards the front, no other screws
    Post by: eric tobin, Jul 21, 2017 in forum: Troubleshooting
  16. eric tobin
    Thread

    Solved cannot remove extruder

    there are no screws where there should be. extruder is being held by something but I cant find it, need to remove to unjam fillament
    Thread by: eric tobin, Jul 21, 2017, 7 replies, in forum: Troubleshooting
Find older messages
Showing results 61 to 76 of 76
Search Again
Page 4 of 4