1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 2 of 2
  1. BronStoppable
    Post

    Answered Can’t change filament

    [MEDIA] as you can see once it clip, it slides then makes a noise, stops but once it starts again it’s no longer in line with the original print.
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  2. BronStoppable
    Post

    Answered Can’t change filament

    It makes a clicking stepper noise as it moves to the left before it hits the tab which is why i thought it was the plate size. Like it expects...
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  3. BronStoppable
    Post

    Answered Can’t change filament

    Just tried, even without filament it didn’t line back up after continuing the print
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  4. BronStoppable
    Post

    Answered Can’t change filament

    Yea I have the quick change add on so it just pops out, switches and then goes back. How would i do that? It releases the filament once it stops...
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  5. BronStoppable
    Post

    Answered Can’t change filament

    I don’t think it’s that, it stays in position once it reaches the stopper.
    Post by: BronStoppable, Nov 13, 2019 in forum: Troubleshooting
  6. BronStoppable
    Thread

    Answered Can’t change filament

    Hey, so whenever i click change filament mid print, everything seems to work fine until i restart it. Once it slides to go back and printing it’s...
    Thread by: BronStoppable, Nov 13, 2019, 14 replies, in forum: Troubleshooting
  7. BronStoppable
    Post

    Answered Changing Filament Mid print Offset?

    Correct, if I use the change filament setting it happens every time but other than that prints and moves normally which is why I thought it was my...
    Post by: BronStoppable, Apr 8, 2019 in forum: Troubleshooting
  8. BronStoppable
    Post

    Answered Changing Filament Mid print Offset?

    Yea i did it right from home and when it got over to the far left stepper it made the noise as if it was trying to go farther, the popped out the...
    Post by: BronStoppable, Apr 7, 2019 in forum: Troubleshooting
  9. BronStoppable
    Post

    Answered Changing Filament Mid print Offset?

    Thanks for responding. I don’t think the steppers are messed up or anything as they only make the noise when part of a print is out of bounds ie:...
    Post by: BronStoppable, Apr 6, 2019 in forum: Troubleshooting
  10. BronStoppable
    Thread

    Answered Changing Filament Mid print Offset?

    Hi, So whenever I use the change filament button on the lcd, it shifts over, makes a grind noise(like when the x goes to far) as it hits the...
    Thread by: BronStoppable, Apr 6, 2019, 7 replies, in forum: Troubleshooting
  11. BronStoppable
    Post

    Answered Help! Prints suddenly brittle

    lol yea I usually put a few drops of oil in it before I print. But i will try both the things you said, thank you again
    Post by: BronStoppable, Nov 16, 2017 in forum: Troubleshooting
  12. BronStoppable
    Post

    Answered Help! Prints suddenly brittle

    I have a oilier clipped on the filament right before it goes into the extruder. I actually think based on what I've read its under extruding but I...
    Post by: BronStoppable, Nov 16, 2017 in forum: Troubleshooting
  13. BronStoppable
    Post

    Answered Help! Prints suddenly brittle

    Pla 1.75 temp 210/ bed 60.. I used glue stick or painters tape. I'll defiantly check them out. It started out of no where so it kind of threw me off.
    Post by: BronStoppable, Nov 16, 2017 in forum: Troubleshooting
  14. BronStoppable
    Thread

    Answered Help! Prints suddenly brittle

    So I’m new to having my Robo R1 plus and slowly getting the hang of it. I’ve been able to print small things 8 times out of 10. Last week i was...
    Thread by: BronStoppable, Nov 6, 2017, 8 replies, in forum: Troubleshooting
Find older messages
Showing results 21 to 34 of 34
Search Again
Page 2 of 2