1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. mike aguilar
    Post

    Answered First layer of PLA wont stick

    Thanks Mark I will give that a shot and let you know later.
    Post by: mike aguilar, Aug 19, 2017 in forum: Troubleshooting
  2. mike aguilar
    Thread

    Answered First layer of PLA wont stick

    Heya Guys Im sure I posted this before but not a forum junkie here, I got myself another R13D printer but this one is not laying a layer down to...
    Thread by: mike aguilar, Aug 19, 2017, 3 replies, in forum: Troubleshooting
  3. mike aguilar
    Post

    Solved Another Jam / Clog new R1 plus

    After assembling and running I believe "these violent delights have violent ends" came out good Thanks Mark again for your time! [ATTACH]
    Post by: mike aguilar, Jan 21, 2017 in forum: Troubleshooting
  4. mike aguilar
    Post

    Solved Another Jam / Clog new R1 plus

    Thank you Mark much appreciated on ur time let's hope I'm back to printing soon
    Post by: mike aguilar, Jan 21, 2017 in forum: Troubleshooting
  5. mike aguilar
    Post

    Solved Another Jam / Clog new R1 plus

    I got it cleared I boiled it in water cleaned it out good and used air can on it reassembling right now
    Post by: mike aguilar, Jan 21, 2017 in forum: Troubleshooting
  6. mike aguilar
    Post

    Solved Another Jam / Clog new R1 plus

    Ok it's off but still stuck in there good any recommendations? [ATTACH]
    Post by: mike aguilar, Jan 21, 2017 in forum: Troubleshooting
  7. mike aguilar
    Post

    Solved Another Jam / Clog new R1 plus

    Thank you Mark I will give it a shot and see
    Post by: mike aguilar, Jan 21, 2017 in forum: Troubleshooting
  8. mike aguilar
    Thread

    Solved Another Jam / Clog new R1 plus

    I'm at my wits end here in pic I have same issue l, filament stuck in hotend and will not come out this seems to be jammed clogged whatever temp...
    Thread by: mike aguilar, Jan 21, 2017, 10 replies, in forum: Troubleshooting
  9. mike aguilar
    Post

    Unresolved Extruder wont release filament after heating up

    Thanks guys I will look into this as well as seeing if this fixes. Much appreciated !
    Post by: mike aguilar, May 4, 2016 in forum: Troubleshooting
  10. mike aguilar
    Post

    Unresolved Extruder wont release filament after heating up

    Havent used a oiler yet im sure that will add ease to it or help this issue from happening again.
    Post by: mike aguilar, May 4, 2016 in forum: Troubleshooting
  11. mike aguilar
    Post

    Unresolved Extruder wont release filament after heating up

    Ok thanks for replying it's a robo 3D plus I usually heat it up to 210 to run. I load it around 185 as it says on printer. Anymore info needed...
    Post by: mike aguilar, May 3, 2016 in forum: Troubleshooting
  12. mike aguilar
    Thread

    Unresolved Extruder wont release filament after heating up

    Ok I took a break from printing things for awhile as I finished a Fallout clock for my daughter. It was cool and I was happy and she loved it. The...
    Thread by: mike aguilar, May 3, 2016, 7 replies, in forum: Troubleshooting
  13. mike aguilar
    Post

    Solved My Robo3d printer+ adventures

    Worked like a charm Thanks So much Mark!
    Post by: mike aguilar, Apr 7, 2016 in forum: Troubleshooting
  14. mike aguilar
    Thread

    Solved My Robo3d printer+ adventures

    Hello, I recently purchased my 3d printer 3 weeks ago, taking all the precations and reading very carefully along with watching all the youtube...
    Thread by: mike aguilar, Apr 7, 2016, 2 replies, in forum: Troubleshooting
Showing results 1 to 14 of 14
Search Again