1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 6
  1. castmemberzack
    Thread

    ABS Troubles with ABS

    I'm getting stuff like this: http://imgur.com/a/z3QUb Hatchbox, R1+, S3D. Here's the file: http://www.thingiverse.com/thing:317788
    Thread by: castmemberzack, Aug 5, 2016, 12 replies, in forum: Printing Filament
  2. castmemberzack
    Post

    Unanswered Hex fan isn't working.

    Jst connectors.
    Post by: castmemberzack, Jul 21, 2016 in forum: Troubleshooting
  3. castmemberzack
    Thread

    Unanswered Hex fan isn't working.

    I just ordered a new one, and it does the same thing. I pull on the black plastic tube that houses all the wires in a certain direction, it works....
    Thread by: castmemberzack, Jul 21, 2016, 4 replies, in forum: Troubleshooting
  4. castmemberzack
    Thread

    Unanswered Getting bumps on ABS that throw off my extruder

    http://m.imgur.com/Qv2kWqbkWqb The middle and outside of the prints are fine. It's when it gets to those edgez that it lifts up on one side and...
    Thread by: castmemberzack, Jul 14, 2016, 0 replies, in forum: Troubleshooting
  5. castmemberzack
    Post

    Unanswered Edges are warping up.

    http://m.imgur.com/fOnk8yQ see if that works.
    Post by: castmemberzack, Jun 27, 2016 in forum: Troubleshooting
  6. castmemberzack
    Post

    Unanswered Edges are warping up.

    http://imgur.com/fOnk8yQyQ Here you are. It's the best pic I could get. And no, thank you!
    Post by: castmemberzack, Jun 27, 2016 in forum: Troubleshooting
  7. castmemberzack
    Post

    Unanswered Edges are warping up.

    S3D. The problem is that I think it's TOO squished. I'll upload pics in a second of the first layer.
    Post by: castmemberzack, Jun 27, 2016 in forum: Troubleshooting
  8. castmemberzack
    Post

    Unanswered Edges are warping up.

    Well I just did an M565 and it told me my Z offset was at -0.74, which I don't think is correct for the R1+. Oh and I have the R1+. Knew I was...
    Post by: castmemberzack, Jun 27, 2016 in forum: Troubleshooting
  9. castmemberzack
    Thread

    Unanswered Edges are warping up.

    I've tried turning the plate and extruder temp down. Extruder temp is at 190 and plate was at 50. http://imgur.com/a/CA74G Everything's being...
    Thread by: castmemberzack, Jun 27, 2016, 11 replies, in forum: Troubleshooting
  10. castmemberzack
    Post

    Unanswered Layers aren't being finished

    Can you point me to that thread? I'll give it a tr i the shims don't work. I actually just bought a bunch of round magnets to hold paper towels in...
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
  11. castmemberzack
    Post

    Unanswered Layers aren't being finished

    I'm 90% sure the bed is not level. Like one end is higher. Is that possible?
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
  12. castmemberzack
    Post

    Unanswered Layers aren't being finished

    Didn't ix it but made it a little bit better.
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
  13. castmemberzack
    Post

    Unanswered Layers aren't being finished

    That may have just solved it. BRB.
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
  14. castmemberzack
    Post

    Unanswered Layers aren't being finished

    About the same. Just not adhering to the plate as well.
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
  15. castmemberzack
    Post

    Unanswered Layers aren't being finished

    When I told the threaded rod while it's printing, it gives me an okay print. But when I go back and make it restart, it's like it starts from...
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
  16. castmemberzack
    Post

    Unanswered Layers aren't being finished

    Should I just keep raising that side till that disappears? Will that solve the problem?
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
  17. castmemberzack
    Post

    Unanswered Layers aren't being finished

    Now it's printing out thin on one side and nicely on the other leading to what looks like over extrusion. http://m.imgur.com/QNNP8OT
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
  18. castmemberzack
    Post

    Unanswered Layers aren't being finished

    I'm such a dork sometimes haha Yes I leveled it with the piece of paper to the best of my abilities. Still no go. Should I have leveled it with...
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
  19. castmemberzack
    Post

    Unanswered Layers aren't being finished

    http://m.imgur.com/9RjEr5e,7hSfIQZ,ubNhDOAubNhDOA Here are some pictures that might help. Anything?
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
  20. castmemberzack
    Post

    Unanswered Layers aren't being finished

    It does do both G28 and 29 automatically if that's what you're asking.
    Post by: castmemberzack, Jun 19, 2016 in forum: Troubleshooting
Showing results 1 to 20 of 106 Next >
Search Again
Page 1 of 6