1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Peter Joseph Rosado
    Post

    Solved Power supply connectors

    Thanks so much.
    Post by: Peter Joseph Rosado, Sep 9, 2018 in forum: Troubleshooting
  2. Peter Joseph Rosado
    Thread

    Solved Power supply connectors

    I recently ordered a new aduino board for my printer because it was burnt out. I got my new one today but I noticed that the connectors that go...
    Thread by: Peter Joseph Rosado, Sep 8, 2018, 2 replies, in forum: Troubleshooting
  3. Peter Joseph Rosado
    Thread

    Answered Power supply

    Hello there, Have a question, I have a Robo 3D R1+ and the power supply seems to be giving out on me. I have another from another printer that in...
    Thread by: Peter Joseph Rosado, Aug 30, 2018, 1 replies, in forum: Troubleshooting
  4. Peter Joseph Rosado
    Thread

    Unresolved Voltage problems?

    Im having trouble with my printer. While on stand by the printer is fine, however as soon as I preheat the extruder and the bed the lights on the...
    Thread by: Peter Joseph Rosado, Jan 3, 2018, 3 replies, in forum: Troubleshooting
  5. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    That means that I can get one with the thermistor already installed. It's just connect it and make adjustments to the matter control?
    Post by: Peter Joseph Rosado, Jan 7, 2017 in forum: Troubleshooting
  6. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    If I replace the hot end what kind of hot end can I use or is it a one size fits all thing.
    Post by: Peter Joseph Rosado, Jan 7, 2017 in forum: Troubleshooting
  7. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    As far as I can tell there is no screw. Unless it's at the bottom of the hot end I can't tell cause of the residue on the hot end.
    Post by: Peter Joseph Rosado, Jan 7, 2017 in forum: Troubleshooting
  8. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    Hot end. Sorry it's a bit black last print I made got clupped up and did that mess. XD
    Post by: Peter Joseph Rosado, Jan 7, 2017 in forum: Troubleshooting
  9. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    Robo 3D R1
    Post by: Peter Joseph Rosado, Jan 7, 2017 in forum: Troubleshooting
  10. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    Disconnected and reconnected wires and it worked for a while and got a few prints off but anything that required more than an hour of print shuts...
    Post by: Peter Joseph Rosado, Jan 7, 2017 in forum: Troubleshooting
  11. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    Then the fan is in working order im stillngoimg to open the bottom panel to clean it out just in case. Before hand I saw the gcode and it said the...
    Post by: Peter Joseph Rosado, Jan 6, 2017 in forum: Troubleshooting
  12. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    It's on but the air is faint.
    Post by: Peter Joseph Rosado, Jan 6, 2017 in forum: Troubleshooting
  13. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    Do I just open the bottom panel to check to see if it not blocked or anything? There wouldnt be a problem?
    Post by: Peter Joseph Rosado, Jan 6, 2017 in forum: Troubleshooting
  14. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    Both Side fan and Bottom fan are on constantly while printing but cant check prolonged times since printer shuts down due to error.
    Post by: Peter Joseph Rosado, Jan 6, 2017 in forum: Troubleshooting
  15. Peter Joseph Rosado
    Post

    Unresolved 3D printer turns off completely

    Verified the GCode and yes theres a message that the temp is too low and makes my printer completely shut down. How do I get to the thermistor to...
    Post by: Peter Joseph Rosado, Jan 6, 2017 in forum: Troubleshooting
  16. Peter Joseph Rosado
    Thread

    Unresolved 3D printer turns off completely

    3D printer printing as normal and out of nowhere it shutdown completely. Restarted everything and it seems to be working again until 15 minutes...
    Thread by: Peter Joseph Rosado, Jan 6, 2017, 28 replies, in forum: Troubleshooting
Showing results 1 to 16 of 16
Search Again