1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. TheKoopaGaming
    Thread

    Answered Autoleveling not working after RAMPS replacement

    Hey, you guys have been very helpful in the past, hoping you can help me solve this problem. I just replaced my RAMPS board, and everything seems...
    Thread by: TheKoopaGaming, Oct 3, 2018, 4 replies, in forum: Troubleshooting
  2. TheKoopaGaming
    Post

    Unanswered X-Axis Shifting

    Could it be anything besides this? I have repeatedly checked both and neither seem to be the problem. Could it be a code issue? Another thing is...
    Post by: TheKoopaGaming, May 13, 2017 in forum: Troubleshooting
  3. TheKoopaGaming
    Post

    Unanswered X-Axis Shifting

    This is happening on both the X and Y axis. Nothing jammed in the belt- it moves around just fine. Bed moves freely, what would be blocking this?
    Post by: TheKoopaGaming, May 13, 2017 in forum: Troubleshooting
  4. TheKoopaGaming
    Post

    Unanswered X-Axis Shifting

    How do I go about fixing this?
    Post by: TheKoopaGaming, May 12, 2017 in forum: Troubleshooting
  5. TheKoopaGaming
    Post

    Unanswered X-Axis Shifting

    Thanks for the answer! Not sure if this would change anything but at the start of my prints there is often a grinding noise whenever the bed...
    Post by: TheKoopaGaming, May 12, 2017 in forum: Troubleshooting
  6. TheKoopaGaming
    Thread

    Unanswered X-Axis Shifting

    Hello Robo Community I have been having a problem with x-axis shifting. Whenever I try and print a model that takes up most of the build plate on...
    Thread by: TheKoopaGaming, May 9, 2017, 10 replies, in forum: Troubleshooting
  7. TheKoopaGaming
    Post

    Solved Problems Printing with PETG

    Figured this out- had to change the start gcode in Cura to get the z offset to stay set where it is. Thanks for the help!! Sent from my iPhone...
    Post by: TheKoopaGaming, Apr 22, 2017 in forum: Troubleshooting
  8. TheKoopaGaming
    Post

    Solved Problems Printing with PETG

    I'm using an XXL controller and I set the z offset to 1.5mm before the print but when I checked after the print started the controller had it set...
    Post by: TheKoopaGaming, Apr 21, 2017 in forum: Troubleshooting
  9. TheKoopaGaming
    Thread

    Solved Problems Printing with PETG

    Hello Robo Community You have been very helpful to me in the past so I hope you can help me now. This is my first time printing with PETG and I am...
    Thread by: TheKoopaGaming, Apr 21, 2017, 3 replies, in forum: Troubleshooting
  10. TheKoopaGaming
    Thread

    Solved Layer Shifting

    Hello Forum! You have been very helpful in the past so I hope you can help now! Ever since I did a little maintenance on my printer (nothing...
    Thread by: TheKoopaGaming, Feb 24, 2017, 2 replies, in forum: Troubleshooting
  11. TheKoopaGaming
    Post

    Best Robo R1+ mods

    PEI is your best friend! It is sheet of plastic that you can put on your bed and everything sticks great to it. No glue or hairspray. There are...
    Post by: TheKoopaGaming, Dec 21, 2016 in forum: Mods and Upgrades
  12. TheKoopaGaming
    Post

    PEI Problem

    What temperature would you recommend? Sent from my iPhone using Tapatalk
    Post by: TheKoopaGaming, Sep 22, 2016 in forum: Mods and Upgrades
  13. TheKoopaGaming
    Post

    PEI Problem

    Ok thanks for all the help. I got the first layer to stick down ok, I'm im still getting warping at the corners only a few layers in. Any advice....
    Post by: TheKoopaGaming, Sep 22, 2016 in forum: Mods and Upgrades
  14. TheKoopaGaming
    Post

    PEI Problem

    Anyone? Sent from my iPhone using Tapatalk
    Post by: TheKoopaGaming, Sep 20, 2016 in forum: Mods and Upgrades
  15. TheKoopaGaming
    Post

    PEI Problem

    What do I want to do to get the best first later? Sent from my iPhone using Tapatalk
    Post by: TheKoopaGaming, Sep 19, 2016 in forum: Mods and Upgrades
  16. TheKoopaGaming
    Thread

    PEI Problem

    Hello- I've been reading up on using PEI and I just got some today. I installed it and went to test it out any nothing is sticking. I printing...
    Thread by: TheKoopaGaming, Sep 18, 2016, 10 replies, in forum: Mods and Upgrades
  17. TheKoopaGaming
    Post

    Solved Bubbling on First Layer

    Ok I'll try lowering the bed tempature. I don't usually print that hot, that was just the default in Cura and I forgot to change it. Thanks for...
    Post by: TheKoopaGaming, Sep 12, 2016 in forum: Troubleshooting
  18. TheKoopaGaming
    Post

    Solved Bubbling on First Layer

    Sorry PLA. Though I out that in.
    Post by: TheKoopaGaming, Sep 12, 2016 in forum: Troubleshooting
  19. TheKoopaGaming
    Post

    Solved Bubbling on First Layer

    I'm using RoBo 3d brand filament (not the stuff the came with the printer) at 210 with the bed at 60. Do I need to change the bed tempature or do...
    Post by: TheKoopaGaming, Sep 12, 2016 in forum: Troubleshooting
  20. TheKoopaGaming
    Thread

    Solved Bubbling on First Layer

    Hello- I have had my R1 PLUS for roughly a month and a half, and have loved it. My problem is that recently I have been noticing a lot of...
    Thread by: TheKoopaGaming, Sep 11, 2016, 10 replies, in forum: Troubleshooting
Showing results 1 to 20 of 21 Next >
Search Again
Page 1 of 2