1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. jason rowsey
    Post

    Allen Key sizes

    Metric, correct? LOL MM so of course it is metric...
    Post by: jason rowsey, Jan 29, 2018 in forum: Troubleshooting
  2. jason rowsey
    Thread

    Allen Key sizes

    Hey all, can anyone tell me the sizes of the hex keys for the R2 printer? I stripped one of mine and wanted to pick one up on my way home from...
    Thread by: jason rowsey, Jan 29, 2018, 5 replies, in forum: Troubleshooting
  3. jason rowsey
    Post

    Robo R2 shuts down after 3-4% when printing large prints

    Yes, as soon as I changed power bricks, the issue has never happened again. I have done 40+ hour prints with no turn off.
    Post by: jason rowsey, Jan 29, 2018 in forum: Troubleshooting
  4. jason rowsey
    Post

    Robo R2 shuts down after 3-4% when printing large prints

    This was happening to me as well, after about an 1 - 3 hours of printing normally, the printer would turn off. My issue was the power brick. I...
    Post by: jason rowsey, Jan 29, 2018 in forum: Troubleshooting
  5. jason rowsey
    Post

    Heating Failed, system stopped. Heater ID: bed

    I am using a Reese foil wrapper folded to bridge the connection of the prongs and the heat plate. I am not getting any error message and that is...
    Post by: jason rowsey, Oct 11, 2017 in forum: Troubleshooting
  6. jason rowsey
    Post

    Heating Failed, system stopped. Heater ID: bed

    Can you see the pictures? If not here is a facebook link....
    Post by: jason rowsey, Oct 11, 2017 in forum: Troubleshooting
  7. jason rowsey
    Post

    Heating Failed, system stopped. Heater ID: bed

    [IMG] [IMG] [IMG]
    Post by: jason rowsey, Oct 11, 2017 in forum: Troubleshooting
  8. jason rowsey
    Post

    Heating Failed, system stopped. Heater ID: bed

    I will as soon as my print finishes or something goes wrong. That might be a day or 2. I just ripped it in half folded it an balanced it on the 2...
    Post by: jason rowsey, Oct 9, 2017 in forum: Troubleshooting
  9. jason rowsey
    Post

    Heating Failed, system stopped. Heater ID: bed

    So I just had this happen to me and was able to fix this with a Reese wrapper folded on the lower prongs. I know that is not a permanent fix, but...
    Post by: jason rowsey, Oct 9, 2017 in forum: Troubleshooting
  10. jason rowsey
    Post

    Screeching y axis

    So an update, I did my best to re align all the belts and made sure everything was tightened. I also added some wd40 to specifice spots on the y...
    Post by: jason rowsey, Aug 11, 2017 in forum: Troubleshooting
  11. jason rowsey
    Post

    Screeching y axis

    [MEDIA]
    Post by: jason rowsey, Aug 9, 2017 in forum: Troubleshooting
  12. jason rowsey
    Profile Post

    I cant attach a file. It is under the file size restriction, I choose the file, and it loads...

    I cant attach a file. It is under the file size restriction, I choose the file, and it loads and just sits on the attachment screen. The only...
    Profile post by jason rowsey for Harry, Aug 9, 2017
  13. jason rowsey
    Post

    Screeching y axis

    Trying to attach video
    Post by: jason rowsey, Aug 9, 2017 in forum: Troubleshooting
  14. jason rowsey
    Thread

    Screeching y axis

    I just want to make clear that this is my fault, I tinkered with the back corner to fix a clicking sound(which worked) but am now getting this...
    Thread by: jason rowsey, Aug 9, 2017, 7 replies, in forum: Troubleshooting
  15. jason rowsey
    Post

    R2 power supply

    does everyone elses power supply hum? I was supprised at the noise level of it when I plugged it in.
    Post by: jason rowsey, Jul 28, 2017 in forum: General Questions
Showing results 1 to 15 of 15
Search Again