1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Gripp
    Post

    Partial Answer Hotend Turns off after autolevel

    I didn't get a chance to copy and past my s3d pronterface info. But I did go ahead and order a new thermistor. My E3D V6 uses the metal tube thing...
    Post by: Gripp, Aug 10, 2017 in forum: Troubleshooting
  2. Gripp
    Thread

    Partial Answer Hotend Turns off after autolevel

    I've been having an issue where by hot end seems to turn off after autolevel. I can get the print to run again, but I have to go to my lcd display...
    Thread by: Gripp, Aug 8, 2017, 9 replies, in forum: Troubleshooting
  3. Gripp
    Post

    Simplify3D

    Thanks for the GCode. Seemed to work (put in my own z-offest) for what I need. With the caveat that I preheat before I hit print. It started...
    Post by: Gripp, Jul 17, 2017 in forum: Software
  4. Gripp
    Thread

    Simplify3D

    So I broke down and bought a copy of S3D. I can't seem to get it to raise the z offset. I copied over my script from cura for starting and ending....
    Thread by: Gripp, Jul 15, 2017, 6 replies, in forum: Software
  5. Gripp
    Post

    Solved Extruder motor

    The gear came off, but the peg shape on the new motor only had one flat side, so I heated it with the hair dryer to get it on. Had to look into...
    Post by: Gripp, Jul 15, 2017 in forum: Troubleshooting
  6. Gripp
    Thread

    Solved Extruder motor

    So my extruder motor or motor cable seems to have went. The motor just clicks but doesn't fully turn, except on retraction. I bought a replacement...
    Thread by: Gripp, Jul 14, 2017, 3 replies, in forum: Troubleshooting
  7. Gripp
    Post

    Answered E3D V6 Loose on R1+

    Just changed these numbers and I'm about to do a test print. The defaults were 9000,9000,100,10000. That's quite the difference.
    Post by: Gripp, Jun 15, 2017 in forum: Troubleshooting
  8. Gripp
    Post

    Answered E3D V6 Loose on R1+

    Where in the firmware do I change this (config H?) and what is a good value to start with? I was printing that at like 45mm/s.
    Post by: Gripp, Jun 15, 2017 in forum: Troubleshooting
  9. Gripp
    Post

    Answered E3D V6 Loose on R1+

    It was the first link posted. I remember the white filament. I just put some electric tape around the collar and it's tight now. I'll look into...
    Post by: Gripp, Jun 15, 2017 in forum: Troubleshooting
  10. Gripp
    Post

    Answered E3D V6 Loose on R1+

    Cool. I'll check when I get home. Do you happen to know how high it should be?
    Post by: Gripp, Jun 12, 2017 in forum: Troubleshooting
  11. Gripp
    Post

    Answered E3D V6 Loose on R1+

    I don't recall off the top of my head, but it was a file for an e3d v6 quick release. Got it on thingiverse.
    Post by: Gripp, Jun 12, 2017 in forum: Troubleshooting
  12. Gripp
    Thread

    Answered E3D V6 Loose on R1+

    I installed a V6 this weekend and when I went to print, I noticed that the whole thing was loose. Loose in the way that you can grab the hot end...
    Thread by: Gripp, Jun 12, 2017, 19 replies, in forum: Troubleshooting
  13. Gripp
    Thread

    E3D V6 install

    So I got my v6 in the mail. I watched a video or 2 and saw that you need to wire the fan, heat element, and thermester into into the board. Can I...
    Thread by: Gripp, Jun 9, 2017, 1 replies, in forum: Mods and Upgrades
  14. Gripp
    Post

    Answered Filament stuck before hotend

    From what I can tell, yes. An Amazon retailer. According to their review and question answers.
    Post by: Gripp, Jun 5, 2017 in forum: Troubleshooting
  15. Gripp
    Post

    Answered Filament stuck before hotend

    I bought an E3 v6. It was only a couple bucks more and I've heard good things. I'll look into printing the required parts for it tomorrow. Been an...
    Post by: Gripp, Jun 5, 2017 in forum: Troubleshooting
  16. Gripp
    Post

    Answered Filament stuck before hotend

    I'll try to unscrew the threads but more than likely I won't have the means to do it. Can I buy a hot end from robo or is there another site? I'm...
    Post by: Gripp, Jun 5, 2017 in forum: Troubleshooting
  17. Gripp
    Post

    Answered Filament stuck before hotend

    Thanks, that was helpful and I was able to clear the jam, but my nozzle just broke when I was tightening it up. Had a heated hot end to make sure...
    Post by: Gripp, Jun 5, 2017 in forum: Troubleshooting
  18. Gripp
    Thread

    Answered Filament stuck before hotend

    there is a piece of filament stuck in the tube between the hot end and the extruder. I've had jams that I've been able to pull out, but this one...
    Thread by: Gripp, Jun 5, 2017, 9 replies, in forum: Troubleshooting
  19. Gripp
    Post

    Installing Fans

    Ok. I'm not ready to attempt any kind of hotend upgrades yet so I'll make sure it's blowing on the part. would it be worth it to replace the...
    Post by: Gripp, May 17, 2017 in forum: Mods and Upgrades
  20. Gripp
    Thread

    Installing Fans

    So I have some 40mm fans laying around and since I'm fairly new to 3D printing and definitely new to the R1+, I figured I'd ask for some input on...
    Thread by: Gripp, May 16, 2017, 4 replies, in forum: Mods and Upgrades
Showing results 1 to 20 of 35 Next >
Search Again
Page 1 of 2