1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Folk Hero
    Post

    Answered G-Code Question

    Thanks. That is a nice setup.
    Post by: Folk Hero, Jun 28, 2017 in forum: General Questions
  2. Folk Hero
    Post

    Answered G-Code Question

    What about putting a line in before shutoff like "G1 E-100 F1500 ;retract filament 100 mm @ 1500mm/min" to extract the filament before it turns off?
    Post by: Folk Hero, Jun 28, 2017 in forum: General Questions
  3. Folk Hero
    Post

    Answered G-Code Question

    I like your idea. I could sleep at night without worrying about the printer running.
    Post by: Folk Hero, Jun 27, 2017 in forum: General Questions
  4. Folk Hero
    Post

    Answered G-Code Question

    Bummer.
    Post by: Folk Hero, Jun 27, 2017 in forum: General Questions
  5. Folk Hero
    Thread

    Answered G-Code Question

    Is there a G-Code that will turn a ROBO 1+ off after a print is finished? Tim
    Thread by: Folk Hero, Jun 27, 2017, 18 replies, in forum: General Questions
  6. Folk Hero
    Thread

    Solved Is this correct?

    Should the number be this low or should I type in the 430 and hit go? [ATTACH]
    Thread by: Folk Hero, Jun 23, 2017, 0 replies, in forum: General Questions
  7. Folk Hero
    Post

    Solved Can't find printer

    So would you just disable it or uninstall it? Tim
    Post by: Folk Hero, Jun 22, 2017 in forum: Troubleshooting
  8. Folk Hero
    Post

    Solved Can't find printer

    Now for that brilliant flash of stupidity on my part. Are you talking about windows device manager? and where in Cura is that command at? Tim
    Post by: Folk Hero, Jun 21, 2017 in forum: Troubleshooting
  9. Folk Hero
    Post

    Answered Detached wires...

    That's the one.
    Post by: Folk Hero, Jun 21, 2017 in forum: Troubleshooting
  10. Folk Hero
    Post

    Solved Can't find printer

    Windoze 8.1, Matter Control 1.5, Cura for ROBO 2.3.1, Craftware 1.14, USB 3 Tim
    Post by: Folk Hero, Jun 21, 2017 in forum: Troubleshooting
  11. Folk Hero
    Thread

    Solved Can't find printer

    I've been trying to use CURA and Craftware, but neither can find the printer. Matter Control hooks right up, but others don't find it. Tim
    Thread by: Folk Hero, Jun 20, 2017, 9 replies, in forum: Troubleshooting
  12. Folk Hero
    Thread

    Solved Matter Control and thermistor

    Since prints can take a long time I go to bed while they are printing and when I wake up the print has finished, but since Matter Control shuts...
    Thread by: Folk Hero, Jun 16, 2017, 0 replies, in forum: General Questions
  13. Folk Hero
    Post

    Solved Not Sticking

    Unfortunately they are out. But I have one of those Lack tables from IKEA on my other printer and it works pretty well especially at only $6.99...
    Post by: Folk Hero, Jun 14, 2017 in forum: Troubleshooting
  14. Folk Hero
    Post

    Solved Not Sticking

    Maybe I'll swing by IKEA and grab a Lack table.
    Post by: Folk Hero, Jun 14, 2017 in forum: Troubleshooting
  15. Folk Hero
    Post

    Solved Not Sticking

    Do you have a number I should dial in/shoot for? Tim
    Post by: Folk Hero, Jun 14, 2017 in forum: Troubleshooting
  16. Folk Hero
    Post

    Solved Not Sticking

    What temp would you run the bed at? Tim
    Post by: Folk Hero, Jun 14, 2017 in forum: Troubleshooting
  17. Folk Hero
    Thread

    Solved Not Sticking

    I'm having a problem with prints not sticking to the right side of the bed. No matter what I do on larger prints they want to lift. I'm running...
    Thread by: Folk Hero, Jun 13, 2017, 16 replies, in forum: Troubleshooting
  18. Folk Hero
    Post

    Solved What is this?

    Thanks that covered my questions. Tim
    Post by: Folk Hero, Jun 7, 2017 in forum: General Questions
  19. Folk Hero
    Thread

    Solved What is this?

    When I print there is a single string silhouette of what I'm printing about ½" away from the print. It doesn't appear to be connected to...
    Thread by: Folk Hero, Jun 6, 2017, 3 replies, in forum: General Questions
  20. Folk Hero
    Post

    Solved Broken Piece

    Thanks but I made a temporary fix that held long enough for me to print some (Whew) Tim
    Post by: Folk Hero, Jun 2, 2017 in forum: Troubleshooting
Showing results 1 to 20 of 34 Next >
Search Again
Page 1 of 2