1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 2
  1. Gary Fellows
    Post

    Flattened Tessellations

    Considering l am only 1.5 weeks into 3D printing and with the tips and tricks of you guys, l am making progress, slowly. Maybe what l am trying...
    Post by: Gary Fellows, Oct 18, 2017 in forum: General Questions
  2. Gary Fellows
    Post

    Flattened Tessellations

    Geof, I have applied a Z hop over printed parts now and altered the default Z Hop Height of 0.075mm to 0.5mm and shall try this. Regarding your...
    Post by: Gary Fellows, Oct 18, 2017 in forum: General Questions
  3. Gary Fellows
    Thread

    Flattened Tessellations

    How can l prevent a smallish tessellated print from having a flattened peak, refer to image.[ATTACH]
    Thread by: Gary Fellows, Oct 18, 2017, 6 replies, in forum: General Questions
  4. Gary Fellows
    Thread

    0.4mm to 0.2mm Nozzle

    How easy is it to change a 0.4mm supplied nozzle to a 0.2mm nozzle? Easy? Any negatives?
    Thread by: Gary Fellows, Oct 17, 2017, 3 replies, in forum: General Questions
  5. Gary Fellows
    Thread

    Dull Print Bed

    Robo R2 I have is 1 week old. Shiny bed is shiny no more. Used flat scraper over 6 or 7 prints and shine gone. Looks awful, but is this a problem?
    Thread by: Gary Fellows, Oct 16, 2017, 3 replies, in forum: Troubleshooting
  6. Gary Fellows
    Post

    Sticking Prints

    I shall try what you suggest.
    Post by: Gary Fellows, Oct 16, 2017 in forum: Troubleshooting
  7. Gary Fellows
    Thread

    Sticking Prints

    I have been using R2 for 1 week, with a rollercoaster of a ride. On day 1, the scraper within the box pretty much ruined the bed surface....
    Thread by: Gary Fellows, Oct 16, 2017, 3 replies, in forum: Troubleshooting
  8. Gary Fellows
    Post

    Lumpy Bumpy Print Finish Near End of Print

    Hi Mechanixfronti. I have taken the advice, and reduced the print speed. This resulted in a satisfactory print.
    Post by: Gary Fellows, Oct 15, 2017 in forum: General Questions
  9. Gary Fellows
    Post

    Lumpy Bumpy Print Finish Near End of Print

    I can't recall seeing if I can set top thickness using Cura. I'll check tomorrow.
    Post by: Gary Fellows, Oct 13, 2017 in forum: General Questions
  10. Gary Fellows
    Post

    Lumpy Bumpy Print Finish Near End of Print

    I think the fan is 75% eek Speed 50mm/ These were supplied by Colorfabb this week. Many thanks. I know what I'm tomorrow.
    Post by: Gary Fellows, Oct 13, 2017 in forum: General Questions
  11. Gary Fellows
    Post

    Lumpy Bumpy Print Finish Near End of Print

    Nozzle 230C, bed 70C. Middle of range and recommended by Colorfabb earlier this week. Tomorrow, l shall bring Z down by 0.05mm.
    Post by: Gary Fellows, Oct 13, 2017 in forum: General Questions
  12. Gary Fellows
    Post

    Lumpy Bumpy Print Finish Near End of Print

    Sounds like a heep of variables.
    Post by: Gary Fellows, Oct 13, 2017 in forum: General Questions
  13. Gary Fellows
    Post

    Lumpy Bumpy Print Finish Near End of Print

    Here's the lumpy or voids, which only appeared near the end of the print. Print 3mm thick. [ATTACH]
    Post by: Gary Fellows, Oct 13, 2017 in forum: General Questions
  14. Gary Fellows
    Post

    Lumpy Bumpy Print Finish Near End of Print

    The material is Colofabb nGen CPE. Should l bring the Z down by 0.05mm, the smallest increment?
    Post by: Gary Fellows, Oct 13, 2017 in forum: General Questions
  15. Gary Fellows
    Post

    Lumpy Bumpy Print Finish Near End of Print

    I shall upload a picture shortly, once it has cooled down. My next headache shall be the removal, which l follow all the tips, but the print...
    Post by: Gary Fellows, Oct 13, 2017 in forum: General Questions
  16. Gary Fellows
    Thread

    Lumpy Bumpy Print Finish Near End of Print

    Why does the print near the end of printing become lumpy and a poor finish. Out of 6 prints this week, only 2 have been satisfactory, of which 2...
    Thread by: Gary Fellows, Oct 13, 2017, 18 replies, in forum: General Questions
  17. Gary Fellows
    Post

    Binary or ASCII

    Many thanks. Makes sense.
    Post by: Gary Fellows, Oct 12, 2017 in forum: General Questions
  18. Gary Fellows
    Thread

    Binary or ASCII

    Hi all, Should stl export for Robo R2 be Binary or ASCII?
    Thread by: Gary Fellows, Oct 12, 2017, 2 replies, in forum: General Questions
  19. Gary Fellows
    Post

    Erratic Temperature

    Mark, Many thanks for the heads up. :)
    Post by: Gary Fellows, Oct 11, 2017 in forum: Software
  20. Gary Fellows
    Post

    stl File Created by Autodesk Inventor

    Tried to view the download from https://tools3d.azurewebsites.net/, however, when l loaded the file into Cura nothing was observable or too large....
    Post by: Gary Fellows, Oct 11, 2017 in forum: Software
Showing results 1 to 20 of 28 Next >
Search Again
Page 1 of 2