1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. KNI1GHT
    Thread

    Unresolved Print did this after a good start......then.....

    I'm using an R1 Plus that I've had for many years now. Various fixes here and there. It's one of 3 of them I own. But it's been a while since...
    Thread by: KNI1GHT, Sep 28, 2022, 1 replies, in forum: Troubleshooting
  2. KNI1GHT
    Thread

    Unresolved When it rains it pours. Help

    Seems my better of the two R1 Plus printers is starting to be finicky on a daily basis now. Extruder problems at first, that is "KINDA" solved...
    Thread by: KNI1GHT, Apr 15, 2020, 2 replies, in forum: Troubleshooting
  3. KNI1GHT
    Post

    Unresolved R1 Plus Hot end and tip question

    I I've read that too about the E3D v6 in regards to my R1 Plus printers, but I can't find anywhere to buy one. No links seem to be available...
    Post by: KNI1GHT, Apr 11, 2020 in forum: Troubleshooting
  4. KNI1GHT
    Post

    Unresolved R1 Plus Hot end and tip question

    I forgot to mention, that the FYSETC part I ordered had a ton of positive feedback with only one negative stating that the wrong part was sent to...
    Post by: KNI1GHT, Apr 10, 2020 in forum: Troubleshooting
  5. KNI1GHT
    Thread

    Unresolved R1 Plus Hot end and tip question

    Hey folks....call me ignorant.....but for the 5+ years I've been using my (2) R1 Plus printers, I've had nothing but great and good luck with...
    Thread by: KNI1GHT, Apr 10, 2020, 5 replies, in forum: Troubleshooting
  6. KNI1GHT
    Thread

    Unresolved Hiya folks. Texture Question

    Hello again. Mike here. Hope everyone is well. Of my (2) R1 Plus Printers, been using for over 5 years, my current one still prints great,...
    Thread by: KNI1GHT, Apr 7, 2020, 1 replies, in forum: Troubleshooting
  7. KNI1GHT
    Post

    Newbie to the site, but not the printer. Got questions...

    Hello again. Quick update to this dilemma. You guys remember how I had said that I own two R1 Plus Printers and they are both ran off individual...
    Post by: KNI1GHT, Jan 26, 2020 in forum: General Questions
  8. KNI1GHT
    Post

    Newbie to the site, but not the printer. Got questions...

    In the process of doing all this, I decided to go back to the beginning so to speak, with the uninstallation of the arduino drivers, and a re...
    Post by: KNI1GHT, Jan 25, 2020 in forum: General Questions
  9. KNI1GHT
    Post

    Newbie to the site, but not the printer. Got questions...

    The tutorial I used and have been following is this one......
    Post by: KNI1GHT, Jan 25, 2020 in forum: General Questions
  10. KNI1GHT
    Post

    Newbie to the site, but not the printer. Got questions...

    Ok.....I've already swapped with 8 other driver boards......and nothing. Ramps board is new, arduino is pushing 5 years old. But so far, this is...
    Post by: KNI1GHT, Jan 24, 2020 in forum: General Questions
  11. KNI1GHT
    Post

    Newbie to the site, but not the printer. Got questions...

    Yes. That's the first thing I looked at when this all started. My temp is at 180, and manually, it extrudes great. So no clogs. But no motor...
    Post by: KNI1GHT, Jan 24, 2020 in forum: General Questions
  12. KNI1GHT
    Post

    Newbie to the site, but not the printer. Got questions...

    Yes. When I can add links, I'll show you him strutting his stuff.
    Post by: KNI1GHT, Jan 24, 2020 in forum: General Questions
  13. KNI1GHT
    Post

    Newbie to the site, but not the printer. Got questions...

    Ok....it's been several days now, but here's what I have "not" found out from my efforts. Short version...... I own 2 Robo r1 plus printers,...
    Post by: KNI1GHT, Jan 24, 2020 in forum: General Questions
  14. KNI1GHT
    Thread

    Newbie to the site, but not the printer. Got questions...

    Hi folks. Sorry for the long post, but humor me. :-) Mike here. I'm brand new to this Robo3D Forum, but definitely not to the printers. To...
    Thread by: KNI1GHT, Jan 15, 2020, 22 replies, in forum: General Questions
Showing results 1 to 14 of 14
Search Again