1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Corey Brumfield
    Thread

    Prusa i3

    So I am looking for firmware help on my Prusa i3, i added a seconded extruder and have it hooked up, but i cant find all the changes i need to...
    Thread by: Corey Brumfield, Feb 6, 2016, 0 replies, in forum: Off Topic
  2. Corey Brumfield
    Profile Post

    If you have a few minutes to help me out, I would greatly appreciate it.

    If you have a few minutes to help me out, I would greatly appreciate it.
    Profile post by Corey Brumfield for Mike Kelly, Feb 5, 2016
  3. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    Okay the height is fixed, but I still can not get pins to fit, or nuts to screw on bolts. lol
    Post by: Corey Brumfield, Feb 3, 2016 in forum: Troubleshooting
  4. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    FIXED IT SPOT ON 20MM
    Post by: Corey Brumfield, Feb 3, 2016 in forum: Troubleshooting
  5. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    Well I uploaded the firmware and I am printing another cube, fingers crossed
    Post by: Corey Brumfield, Feb 3, 2016 in forum: Troubleshooting
  6. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    when I counted I got 22 threads per inch
    Post by: Corey Brumfield, Feb 3, 2016 in forum: Troubleshooting
  7. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    I will do this when I get home from work today. Thank you guys very much.
    Post by: Corey Brumfield, Feb 3, 2016 in forum: Troubleshooting
  8. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    Well that sucks lol.
    Post by: Corey Brumfield, Feb 3, 2016 in forum: Troubleshooting
  9. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    Yes I did, does the r1 plus say that on the glasss? or does it just have an R1?
    Post by: Corey Brumfield, Feb 3, 2016 in forum: Troubleshooting
  10. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    I am not 100% sure, but I have had the printer since april of 2015, and from my understanding it has always been off as I am describing in the...
    Post by: Corey Brumfield, Feb 3, 2016 in forum: Troubleshooting
  11. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    Well that's the problem, it is off by 3mm on a 20 mm test print, so 15% undersized on the z. So how do I fix that? Thanks for the help so far.
    Post by: Corey Brumfield, Feb 2, 2016 in forum: Troubleshooting
  12. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    I am testing a 20 mm cube right now i will upload the results
    Post by: Corey Brumfield, Feb 2, 2016 in forum: Troubleshooting
  13. Corey Brumfield
    Post

    Unresolved Issues with vertical circles

    I would say oblong in the x. So they are short and wide ovals. i also just tightened both y and x axis pulley gears and they were already both...
    Post by: Corey Brumfield, Feb 2, 2016 in forum: Troubleshooting
  14. Corey Brumfield
    Thread

    Unresolved Issues with vertical circles

    I have some sort of calibration issue that I can not seem to fix. I can not get pieces to fit together correctly when they print apart from each...
    Thread by: Corey Brumfield, Feb 2, 2016, 24 replies, in forum: Troubleshooting
Showing results 1 to 14 of 14
Search Again