1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
Page 1 of 3
  1. momoe
    Post

    Solved Y-axis belt with connectors

    I seem to have broken the connector that holds the y-axis belt to the base plate carriage. It’s what the bolt screws into. I figured the belt...
    Post by: momoe, Jan 4, 2020 in forum: Troubleshooting
  2. momoe
    Thread

    Solved Y-axis belt with connectors

    where is a good source to buy parts for this old R1? my connector that holds the Y-axis belt to the bed rails broke off today.. I went on Robo3d...
    Thread by: momoe, Jan 4, 2020, 5 replies, in forum: Troubleshooting
  3. momoe
    Post

    Solved Heat sink mounting issues

    A little dremel action and now we are good to go
    Post by: momoe, Dec 31, 2019 in forum: Troubleshooting
  4. momoe
    Post

    Solved Heat sink mounting issues

    It’s the R1. I got this the year they released them. I think I got a new part that holds the motor and extruded and I think they sent me the R1+...
    Post by: momoe, Dec 31, 2019 in forum: Troubleshooting
  5. momoe
    Post

    Solved Heat sink mounting issues

    It’s been so long I don’t remember what I’ve replaced on this or not. If I replaces the part that connects to the heat sink, could it be wrong?...
    Post by: momoe, Dec 31, 2019 in forum: Troubleshooting
  6. momoe
    Post

    Solved Heat sink mounting issues

    Ok. I don’t get it. I got the heat sink from matter hackers. It does the same thing. The screws that cross through the extruded to hold it in...
    Post by: momoe, Dec 31, 2019 in forum: Troubleshooting
  7. momoe
    Post

    Solved Heat sink mounting issues

    Yeah. That was a Biden adapter I removed and tried again but I think this was an amazon special I ordered. I went to matterhackers and got the...
    Post by: momoe, Dec 28, 2019 in forum: Troubleshooting
  8. momoe
    Post

    Solved Heat sink mounting issues

    https://www.matterhackers.com/store/l/e3d-v6-heat-sink-1.75mm/sk/MF0S9M79 Would this be the one I need to fit the stock carriage of the R1?
    Post by: momoe, Dec 27, 2019 in forum: Troubleshooting
  9. momoe
    Post

    Solved Heat sink mounting issues

    It’s an original R1 that I updated the screw arms when I broke the hotbed. This thing is old. When I talked with Robo, they said it was the R1+...
    Post by: momoe, Dec 27, 2019 in forum: Troubleshooting
  10. momoe
    Thread

    Solved Heat sink mounting issues

    Hi all. Need help. I dusted off the old printer (robo 3D R1)and am reassembling it after some time. I had to replace the whole hot end from the...
    Thread by: momoe, Dec 26, 2019, 16 replies, in forum: Troubleshooting
  11. momoe
    Post

    Screw size needes

    Thanks. That’s the ones I mean
    Post by: momoe, Nov 18, 2018 in forum: General Questions
  12. momoe
    Thread

    Screw size needes

    Can someone tell me what size and thread the screws are that hold the heat sink in the carriage? I know it’s metric but not sure the thread or...
    Thread by: momoe, Nov 18, 2018, 4 replies, in forum: General Questions
  13. momoe
    Post

    need new parts

    Know where to buy one? I’d print it but my printer is broken
    Post by: momoe, Nov 7, 2018 in forum: Mods and Upgrades
  14. momoe
    Thread

    need new parts

    Anyone know if there is a catalog online where we can look up the parts of the base unit? I have an R1 from back in the day and I need the piece...
    Thread by: momoe, Nov 7, 2018, 7 replies, in forum: Mods and Upgrades
  15. momoe
    Thread

    Unresolved Temp error help

    I am getting a max temp error out of the blue. can anyone help me sleuth this out? from Simplify3D: Connected to machine! READ: echo: External...
    Thread by: momoe, Feb 12, 2017, 2 replies, in forum: Troubleshooting
  16. momoe
    Thread

    Partial Answer Whole hot end and heatsync are loose

    so I've noticed the whole hot end is loose. It is seated up in the carrier all the way and the screws are all the way in but they won't get tight...
    Thread by: momoe, Feb 6, 2017, 1 replies, in forum: Troubleshooting
  17. momoe
    Post

    External PID controller for extruder heating?

    Where do you screw yours in?
    Post by: momoe, Feb 6, 2017 in forum: Mods and Upgrades
  18. momoe
    Post

    External PID controller for extruder heating?

    I have a robo3d just before the R1 came out. I have a e3dv6 volcano but I did the screw upgrade and firmware to the R1. Does this screw stud need...
    Post by: momoe, Jan 30, 2017 in forum: Mods and Upgrades
  19. momoe
    Post

    External PID controller for extruder heating?

    My issue is the wire breaks at the bead. If I can stop that, I'm good
    Post by: momoe, Jan 30, 2017 in forum: Mods and Upgrades
  20. momoe
    Post

    External PID controller for extruder heating?

    Metal stud? Do you have a link?
    Post by: momoe, Jan 30, 2017 in forum: Mods and Upgrades
Showing results 1 to 20 of 60 Next >
Search Again
Page 1 of 3