1. Got a question or need help troubleshooting? Post to the troubleshooting forum or Search the forums!
Search Again
  1. Robotron
    Thread

    Unresolved Y axis Stepper motor Specs ? Y axis problem

    Am having problems with my Y-axis. It goes in one direction and not the other. I replaced the stepper drivers/ramps and Arduino. The Y axis...
    Thread by: Robotron, May 11, 2017, 1 replies, in forum: Troubleshooting
  2. Robotron
    Thread

    Solved Err: MAXTEMP BED

    I keep getting a Err: MAXTEMP BED. When i check the pin on T1 for the bed it seems like the black wire melted. I turned on the bed once more when...
    Thread by: Robotron, Jan 9, 2017, 0 replies, in forum: Troubleshooting
  3. Robotron
    Post

    Solved After E3D v6 hotend upgrade cant get clean print , Help !

    my left rod was warped that caused the shaking on the printer. Also found that my fan was not spinning to cool the Mega. I had a brush less fan...
    Post by: Robotron, Jun 14, 2016 in forum: Troubleshooting
  4. Robotron
    Post

    Solved Help with Frameware Uploading error" TimeOut communicating with programmer"

    You are correct the normal Arduino mega is running flawlessly ! I also found that the fan on the bottom of the printer that cools the Arduino was...
    Post by: Robotron, Jun 14, 2016 in forum: Troubleshooting
  5. Robotron
    Post

    Solved Help with Frameware Uploading error" TimeOut communicating with programmer"

    I found the problem the Taurino classic mega board is corrupt. when i plug in my spare Arduino mega board and upload the frameware / other...
    Post by: Robotron, Jun 10, 2016 in forum: Troubleshooting
  6. Robotron
    Post

    Solved Help with Frameware Uploading error" TimeOut communicating with programmer"

    I just restarted my computer then re-uploaded the frame ware to the mega and it worked as far as uploading with no errors. I ran into a new...
    Post by: Robotron, Jun 9, 2016 in forum: Troubleshooting
  7. Robotron
    Thread

    Solved Help with Frameware Uploading error" TimeOut communicating with programmer"

    Hey ! I need help solving this problem. I just got done installing the Lead screw upgrade kit from robo 3d on my robo 3d r1 model printer. I went...
    Thread by: Robotron, Jun 9, 2016, 7 replies, in forum: Troubleshooting
  8. Robotron
    Thread

    Solved After E3D v6 hotend upgrade cant get clean print , Help !

    Hello ! I have a Robo 3d R1 with 8mm thread rodes and E3D v6 hotend upgrade. I cant seem to get any clean prints with this E3D v6 hotend, i don't...
    Thread by: Robotron, May 7, 2016, 4 replies, in forum: Troubleshooting
  9. Robotron
    Post

    Solved MAX TEMP Error on E3D v6 Hotend

    @mark tomlinson Am getting a reading of 1.4 ohms at the connector marked THREM that go's into the RAMPS board port T0. Do you think the whole E3D...
    Post by: Robotron, Feb 16, 2016 in forum: Troubleshooting
  10. Robotron
    Post

    Solved MAX TEMP Error on E3D v6 Hotend

    LCD display
    Post by: Robotron, Feb 16, 2016 in forum: Troubleshooting
  11. Robotron
    Post

    Solved MAX TEMP Error on E3D v6 Hotend

    @mark @woferry In Configuration.h Am i definding a new variable for #define TEMP_SENSOR_0 5 or am i changing the first variable from a _0 1 to _0...
    Post by: Robotron, Feb 16, 2016 in forum: Troubleshooting
  12. Robotron
    Thread

    Solved MAX TEMP Error on E3D v6 Hotend

    I just installed a E3D v6 Hotend and i am getting the following error. " Err: MAXTEMP " this is displaying on my LCD the temp is displaying at...
    Thread by: Robotron, Feb 16, 2016, 10 replies, in forum: Troubleshooting
Showing results 1 to 12 of 12
Search Again